Assessment of the creep life of adhesively bonded joints using the end notched flexure samples

被引：14
作者：
Carneiro Neto, R. M. [1 ]
Akhavan-Safar, A. [2 ]
Sampaio, E. M. [3 ]
Assis, J. T. [3 ]
da Silva, L. F. M. [4 ]
机构：
[1] Fed Univ Rio Janeiro, Ctr Technol & Applicat Composite Mat, Macae, RJ, Brazil
[2] Inst Sci & Innovat Mech & Ind Engn INEGI, Rua Dr Roberto Frias, P-4200465 Porto, Portugal
[3] Univ Estado Rio De Janeiro, Polytech Inst, Lab Adhes & Adherence, Nova Friburgo, RJ, Brazil
[4] Univ Porto, Fac Engn, Dept Engn Mecan, Rua Dr Roberto Frias, P-4200465 Porto, Portugal
来源：
ENGINEERING FAILURE ANALYSIS | 2022年 / 133卷
关键词：
Creep; ENF test; Creep fracture energy; Mode II; Bonded joints; Durability; FAILURE;
D O I：
10.1016/j.engfailanal.2021.105969
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
The behavior of polymeric adhesives is time and temperature dependent, as they are considered viscoelastic materials. These materials can undergo creep deformation even at low stress levels and room temperature. This way, a viscous flow can occur at the adhesive layer and it can lead to viscous deformation, causing a modification in the adhesive properties. The current work aims to investigate the shear creep fracture energy of an epoxy adhesive using end notched flexure (ENF) samples creep tested until failure. The endurance creep limit for cracked bonded joints subjected to pure shear loading conditions is also investigated using ENF samples, representing the maximum creep load which ENF bonded joints can sustain without creep fracture after a specified time. The GIICr-life curve was obtained where the GIIcr is the mode II creep fracture energy. Results showed that small changes in creep load can significantly change the creep endurance limit. Creep fracture energy can be employed for joint design against creep service loads.
引用
收藏
页数：9
相关论文
共 50 条
  • [21] Non-Destructive Inspection of Adhesively Bonded Joints using Amplitude Modulated Thermography
    Wu, X.
    Peters, K.
    EXPERIMENTAL MECHANICS, 2015, 55 (08) : 1485 - 1501
  • [22] Strength Improvement of Adhesively-Bonded Joints Using a Reverse-Bent Geometry
    Campilho, R. D. S. G.
    Pinto, A. M. G.
    Banea, M. D.
    Silva, R. F.
    da Silva, L. F. M.
    JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY, 2011, 25 (18) : 2351 - 2368
  • [23] Non-Destructive Inspection of Adhesively Bonded Joints using Amplitude Modulated Thermography
    X. Wu
    K. Peters
    Experimental Mechanics, 2015, 55 : 1485 - 1501
  • [24] Modelling the environmental degradation of adhesively bonded aluminium and composite joints using a CZM approach
    Lijedahl, C. D. M.
    Crocombe, A. D.
    Wahab, M. A.
    Ashcroft, I. A.
    INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES, 2007, 27 (06) : 505 - 518
  • [25] Ageing of adhesively bonded joints-fracture and failure analysis using video imaging techniques
    Court, RS
    Sutcliffe, MPF
    Tavakoli, SM
    INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES, 2001, 21 (06) : 455 - 463
  • [26] Damage sensing of adhesively-bonded hybrid composite/steel joints using carbon nanotubes
    Lim, Amanda S.
    Melrose, Zachary R.
    Thostenson, Erik T.
    Chou, Tsu-Wei
    COMPOSITES SCIENCE AND TECHNOLOGY, 2011, 71 (09) : 1183 - 1189
  • [27] Damage characterization of adhesively-bonded Bi-material joints using acoustic emission
    Saeedifar, Milad
    Saleh, Mohamed Nasr
    De Freitas, Sofia Teixeira
    Zarouchas, Dimitrios
    COMPOSITES PART B-ENGINEERING, 2019, 176
  • [28] Fracture characterization of human cortical bone under mode II loading using the end-notched flexure test
    Silva, F. G. A.
    de Moura, M. F. S. F.
    Dourado, N.
    Xavier, J.
    Pereira, F. A. M.
    Morais, J. J. L.
    Dias, M. I. R.
    Lourenco, P. J.
    Judas, F. M.
    MEDICAL & BIOLOGICAL ENGINEERING & COMPUTING, 2017, 55 (08) : 1249 - 1260
  • [29] Fracture characterization of human cortical bone under mode II loading using the end-notched flexure test
    F. G. A. Silva
    M. F. S. F. de Moura
    N. Dourado
    J. Xavier
    F. A. M. Pereira
    J. J. L. Morais
    M. I. R. Dias
    P. J. Lourenço
    F. M. Judas
    Medical & Biological Engineering & Computing, 2017, 55 : 1249 - 1260
  • [30] An insight into the mechanical behavior of adhesively bonded plain-woven-composite joints using multiscale modeling
    Hou, Yuliang
    Wang, Weihan
    Meng, Liang
    Sapanathan, Thaneshan
    Li, Jishuai
    Xu, Yingjie
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2022, 219
12345