Novel heat-resistant Al-Si-Ni-Fe alloy manufactured by selective laser melting

被引：38

作者：

Rafael Manca, Dario ^{[1
,4
]}

Churyumov, A. Yu. ^{[1
]}

Pozdniakov, A. V. ^{[1
]}

Ryabov, D. K. ^{[2
]}

Korolev, V. A. ^{[3
]}

Daubarayte, D. K. ^{[3
]}

机构：

[1] NUST MISiS, Leninsky Ave 4, Moscow 119991, Russia

[2] RUSAL Global Management BV, VasilisyKozhinoist 1, Moscow 121096, Russia

[3] LLC Light Mat & Technol Inst UC RUSAL, Leninsky Ave 6b21, Moscow 119991, Russia

[4] Univ Nacl La Plata, Ave 7 776, RA-1900 La Plata, Buenos Aires, Argentina

来源：

MATERIALS LETTERS | 2019年 / 236卷

关键词：

Al-Si-Ni-Fe; Selective laser melting; Aluminium; Alloy; Additive manufacturing; Microstructure; MICROSTRUCTURE; POWDER; FATIGUE; SLM;

D O I：

10.1016/j.matlet.2018.11.033

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The novel Al-Si-Ni-Fe alloy with high compression strength at elevated temperatures has been successfully produced by selective laser melting at an average volumetric energy density of about 100 J/mm(3) and has a relative density of 99,86%. The hardness of as fabricated Al-Si-Ni-Fe alloy is 186HV and it decreases during heat treatment to 124HV due to stress relief and silicon particle growth. The yield compression stress is 355 MPa at 200 degrees C. This high strength is provided by the fine structure formed by the Si, Al5Fe (Ni,Cu) and Al-3(Ni,Cu) phases. The good strength properties of the alloy at elevated temperatures make it a quite promising lightweight material for high temperature applications. (C) 2018 Elsevier B.V. All rights reserved.

引用

页码：676 / 679

页数：4

共 18 条

[1] Additive manufacturing of multi-material structures [J].

Bandyopadhyay, Amit ;

Heer, Bryan .

MATERIALS SCIENCE & ENGINEERING R-REPORTS, 2018, 129 :1-16

[2] Selective laser melting of AlSi10 Mg: Influence of process parameters on Mg2Si precipitation and Si spheroidization [J].

Biffi, C. A. ;

Fiocchi, J. ;

Tuissi, A. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2018, 755 :100-107

[3] Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior [J].

Brandl, Erhard ;

Heckenberger, Ulrike ;

Holzinger, Vitus ;

Buchbinder, Damien .

MATERIALS & DESIGN, 2012, 34 :159-169

[4] High Power Selective Laser Melting (HP SLM) of Aluminum Parts [J].

Buchbinder, D. ;

Schleifenbaum, H. ;

Heidrich, S. ;

Meiners, W. ;

Bueltmann, J. .

LASERS IN MANUFACTURING 2011: PROCEEDINGS OF THE SIXTH INTERNATIONAL WLT CONFERENCE ON LASERS IN MANUFACTURING, VOL 12, PT A, 2011, 12 :271-278

[5] Wear behavior and microstructure of hypereutectic Al-Si alloys prepared by selective laser melting [J].

Kang, Nan ;

Coddet, Pierre ;

Liao, Hanlin ;

Baur, Tiphaine ;

Coddet, Christian .

APPLIED SURFACE SCIENCE, 2016, 378 :142-149

[6] Balling behavior of stainless steel and nickel powder during selective laser melting process [J].

Li, Ruidi ;

Liu, Jinhui ;

Shi, Yusheng ;

Wang, Li ;

Jiang, Wei .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2012, 59 (9-12) :1025-1035

[7] Microstructure and phase formation in Al-20Si-5Fe-3Cu-1Mg synthesized by selective laser melting [J].

Ma, Pan ;

Jia, Yandong ;

Prashanth, Konda Gokuldoss ;

Scudino, Sergio ;

Yu, Zhishui ;

Eckert, Juergen .

JOURNAL OF ALLOYS AND COMPOUNDS, 2016, 657 :430-435

[8]

Petrik J., 2009, MATER ENG, V16, P29

[9] Microstructure and properties of novel AlSi11CuMn alloy manufactured by selective laser melting [J].

Pozdniakov, A. V. ;

Churyumov, A. Yu. ;

Loginova, I. S. ;

Daubarayte, D. K. ;

Ryabov, D. K. ;

Korolev, V. A. .

MATERIALS LETTERS, 2018, 225 :33-36

[10] Development of A1-5Cu/B4C composites with low coefficient of thermal expansion for automotive application [J].

Pozdniakov, A. V. ;

Lotfy, A. ;

Qadir, A. ;

Shalaby, E. ;

Khomutov, M. G. ;

Churyumov, A. Yu. ;

Zolotorevskiy, V. S. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 688 :1-8

← 1 2 →