Sintering behavior of spark plasma sintered alumina with graphene nanoplatelet reinforcement

被引:61
作者
Nieto, Andy [1 ]
Huang, Lin [1 ]
Han, Young-Hwan [2 ]
Schoenung, Julie M. [1 ]
机构
[1] Univ Calif Davis, Dept Chem Engn & Mat Sci, Davis, CA 95616 USA
[2] Yeungnam Univ, Sch Mat Sci & Engn, Kyongsan 712749, South Korea
关键词
Sintering; Nanocomposite; Graphene; SPS; MECHANICAL-PROPERTIES; FRACTURE-TOUGHNESS; TRIBOLOGICAL PROPERTIES; MICROSTRUCTURE; COMPOSITES; CONSOLIDATION; DEFORMATION;
D O I
10.1016/j.ceramint.2015.01.027
中图分类号
TQ174 [陶瓷工业]; TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
Graphene nanoplatelet (GNP) reinforced alumina is synthesized by spark plasma sintering (SPS) using process conditions of 1100-1500 degrees C, 3-10 min dwell time, and 45-90 MPa in order to investigate the effects of GNP on sintering behavior. High volume fractions of GNP (5-15 vol%) are utilized in order to accentuate effects of GNPs. GNP effects on sintering behavior are assessed by evaluating microstructural evolution, grain growth kinetics, and microhardness. The addition of GNPs is found to suppress grain growth by a grain wrapping mechanism resulting in a 10% increase in activation energy when GNP content is increased beyond 5 vol %. Grain growth suppression partially mitigates a decrease in hardness due to the introduction of the soft GNP phase. Evidence of GNPs serving as a sintering aid are seen at short sintering times (3 min), while densification and grain size are observed to level off with extended sintering time (10 min). The application of higher pressures enhances densification, which enables GNPs to more effectively wrap around grains resulting in enhanced grain growth suppression. (C) 2015 Elsevier Ltd and Techna Group S.r.l. All rights reserved.
引用
收藏
页码:5926 / 5936
页数:11
相关论文
共 54 条
[11]   Preparation and Consolidation of Alumina/Graphene Composite Powders [J].
He, Ting ;
Li, Jianlin ;
Wang, Lianjun ;
Zhu, Juanjuan ;
Jiang, Wan .
MATERIALS TRANSACTIONS, 2009, 50 (04) :749-751
[12]   Improved Mechanical Behavior and Plastic Deformation Capability of Ultrafine Grain Alumina Ceramics [J].
Huang, Lin ;
Yao, Wenlong ;
Mukherjee, Amiya K. ;
Schoenung, Julie M. .
JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2012, 95 (01) :379-385
[13]   Scratch-induced deformation in fine- and ultrafine-grained bulk alumina [J].
Huang, Lin ;
Zhang, Zhihui ;
Zhao, Yonghao ;
Yao, Wenlong ;
Mukherjee, Amiya K. ;
Schoenung, Julie M. .
SCRIPTA MATERIALIA, 2010, 63 (05) :528-531
[14]   Tribological properties of Si3N4-graphene nanocomposites [J].
Hvizdos, Pavol ;
Dusza, Jan ;
Balazsi, Csaba .
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2013, 33 (12) :2359-2364
[15]   Structural stability studies of graphene in sintered ceramic nanocomposites [J].
Inam, Fawad ;
Vo, Thuc ;
Bhat, Badekai R. .
CERAMICS INTERNATIONAL, 2014, 40 (10) :16227-16233
[16]   Dynamic grain growth during low-temperature spark plasma sintering of alumina [J].
Kim, Byung-Nam ;
Hiraga, Keijiro ;
Morita, Koji ;
Yoshida, Hidehiro ;
Park, Young-Jo ;
Sakka, Yoshio .
SCRIPTA MATERIALIA, 2014, 80 :29-32
[17]   High-pressure spark plasma sintering of MgO-doped transparent alumina [J].
Kim, Byung-Nam ;
Hiraga, Keijiro ;
Grasso, Salvatore ;
Morita, Koji ;
Yoshida, Hidehiro ;
Zhang, Haibin ;
Sakka, Yoshio .
JOURNAL OF THE CERAMIC SOCIETY OF JAPAN, 2012, 120 (1399) :116-118
[18]   Determination of structural and mechanical properties of multilayer graphene added silicon nitride-based composites [J].
Kun, Peter ;
Tapaszto, Orsolya ;
Weber, Ferenc ;
Balazsi, Csaba .
CERAMICS INTERNATIONAL, 2012, 38 (01) :211-216
[19]   Influence of processing on fracture toughness of Si3N4 + graphene platelet composites [J].
Kvetkova, Lenka ;
Duszova, Annamaria ;
Kasiarova, Monika ;
Dorcakova, Frantiska ;
Dusza, Jan ;
Balazsi, Csaba .
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2013, 33 (12) :2299-2304
[20]   Fracture toughness and toughening mechanisms in graphene platelet reinforced Si3N4 composites [J].
Kvetkova, Lenka ;
Duszova, Annamaria ;
Hvizdos, Pavol ;
Dusza, Jan ;
Kun, Peter ;
Balazsi, Csaba .
SCRIPTA MATERIALIA, 2012, 66 (10) :793-796