Space charge characterisation by EDS microanalysis in spinel MgAl2O4

被引:9
|
作者
Nuns, N [1 ]
Béclin, F [1 ]
Crampon, J [1 ]
机构
[1] Univ Sci & Technol Lille, Lab Struct & Proprietes Etat Solide, ESA 8008, F-59655 Villeneuve Dascq, France
关键词
grain boundaries; spinels; electron microscopy; defects; space charge;
D O I
10.1016/j.jeurceramsoc.2005.03.145
中图分类号
TQ174 [陶瓷工业]; TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
It was already showed that spinet presents a grain boundary sliding deformation accommodated by diffusion during creep at high temperature [Beclin, F, Duclos, R., Crampon, J. and Valin, F, Microstructural superplastic deformation in (MgOAl2O3)-Al-. spinel. Acta Metall. Mater. 1995, 43, 2753-2760; Addad, A., Etude de la plasticite haute temperature, de materiaux ceramiques spinelle-zircone. Ph.D. thesis, Laboratoire de Structure et Proprietes de l'Etat solide, Villeneuve d'Ascq, 1995]. A space charge layer at grain boundary in ionic ceramics can explain the observed interface reaction controlling diffusion at low stress (less than 60 MPa). The nonstoichiometric area due to ionic defects should create an electrostatic potential between the grain surface and inside grain. The purpose of this work is to study the grain boundary region stoichiometry to confirm this theory. Fine-grained spinel (average grain size under micron), which presents an interface reaction at low stresses, is studied by TEM nano-scale microanalysis. The cation ratio Al/Mg variation is well described. It varies from 2.34 at grain boundary to 2.10 at 100 nm inside the grain. The ratio Al/O shows no variation across the grain boundary and suggests that the stoichiometry defect observed is due to an excess of magnesium vacancies located at the grain boundary. (c) 2005 Elsevier Ltd. All rights reserved.
引用
收藏
页码:2809 / 2811
页数:3
相关论文
共 50 条
  • [1] Stoichiometric default in MgAl2O4 spinel:: Space charge in grain boundary investigation
    Béclin, F
    Adadd, A
    Bataille, A
    Crampon, J
    Duclos, R
    EURO CERAMICS VII, PT 1-3, 2002, 206-2 : 763 - 766
  • [2] New synthesis methods of MgAl2O4 spinel
    Pacurariu, C.
    Lazau, I.
    Ecsedi, Z.
    Lazau, R.
    Barvinschi, P.
    Marginean, G.
    JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2007, 27 (2-3) : 707 - 710
  • [3] Improvement of stability of out-layer MgAl2O4 spinel for a Ni/MgAl2O4/Al2O3 catalyst in dry reforming of methane
    Guo, JJ
    Lou, H
    Zhao, H
    Zheng, XM
    REACTION KINETICS AND CATALYSIS LETTERS, 2005, 84 (01): : 93 - 100
  • [4] Improvement of stability of out-layer MgAl2O4 spinel for a Ni/MgAl2O4/Al2O3 catalyst in dry reforming of methane
    Guo J.
    Lou H.
    Zhao H.
    Zheng X.
    Reaction Kinetics and Catalysis Letters, 2005, 84 (1): : 93 - 100
  • [5] Flash-sintering of magnesium aluminate spinel (MgAl2O4) ceramics
    Yoshida, Hidehiro
    Biswas, Papiya
    Johnson, Roy
    Mohan, Mantravadi Krishna
    JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2017, 100 (02) : 554 - 562
  • [6] Synthesis and characterization of nanocrystalline MgAl2O4 spinel via sucrose process
    Alinejad, Babak
    Sarpoolaky, Hosein
    Beitollahi, Ali
    Saberi, Ali
    Afshar, Shahrara
    MATERIALS RESEARCH BULLETIN, 2008, 43 (05) : 1188 - 1194
  • [7] MgAl2O4 spinel synthesis by combustion and detonation reactions: A thermochemical evaluation
    Duraes, L.
    Matias, T.
    Segadaes, A. M.
    Campos, J.
    Portugal, A.
    JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2012, 32 (12) : 3161 - 3170
  • [8] Influence of the sol-gel synthesis on the formation of spinel MgAl2O4
    Parmentier, J
    Richard-Plouet, M
    Vilminot, S
    MATERIALS RESEARCH BULLETIN, 1998, 33 (11) : 1717 - 1724
  • [9] PREPARATION OF MGAL2O4 SPINEL POWDERS VIA FREEZE-DRYING OF ALKOXIDE PRECURSORS
    WANG, CT
    LIN, LS
    YANG, SJ
    JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 1992, 75 (08) : 2240 - 2243
  • [10] The novel low temperature synthesis of nanocrystalline MgAl2O4 spinel using "gel" precursors
    Walker, EH
    Owens, JW
    Etienne, M
    Walker, D
    MATERIALS RESEARCH BULLETIN, 2002, 37 (06) : 1041 - 1050