Particle size effect on the interfacial properties of SiC particle-reinforced Al-Cu-Mg composites

被引:103
作者
Guo, Xiaolei [1 ]
Guo, Qiang [1 ]
Nie, Junhui [2 ]
Liu, Zhiying [1 ]
Li, Zhiqiang [1 ]
Fan, Genlian [1 ]
Xiong, Ding-Bang [1 ]
Su, Yishi [1 ]
Fan, Jianzhong [2 ]
Zhang, Di [1 ]
机构
[1] Shanghai Jiao Tong Univ, State Key Lab Met Matrix Composites, 800 Dongchuan Rd, Shanghai 200240, Peoples R China
[2] Beijing Gen Res Inst Nonferrous Met, Natl Engn & Technol Res Ctr Nonferrous Met Compos, Beijing 100088, Peoples R China
来源
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2018年 / 711卷
关键词
Metal matrix composites; Nanoindentation; Hardness; Interface structure; Geometrically necessary dislocations; METAL-MATRIX COMPOSITES; DEPTH SENSING INDENTATION; FLAKE POWDER-METALLURGY; PRECIPITATION PROCESSES; MECHANICAL-PROPERTIES; VOLUME FRACTION; ALLOYS; STRENGTH; FRACTURE; DEFORMATION;
D O I
10.1016/j.msea.2017.11.068
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
In particle-reinforced metal matrix composites, geometrically necessary dislocations (GNDs) form on the matrix side close to the particle/matrix interface. The mechanical behavior of the bulk composite is affected by the nature of the region populated with GNDs. In this study, the hardness evolution across the reinforcement/matrix interface in 15 vol% SiC particle (SiCp)-reinforced 2009 Al composites with varying particle sizes were studied by nanoindentation with high spatial resolution. The hardness data were then correlated with the microstructures of the composites as well as their bulk tensile properties. It was found that decrease in particle size was associated with a reduction in the punched zone width and an enhancement in the strength of the bulk composite. These findings were interpreted by the effect of GNDs on the ageing kinetics of the matrix, and the improved load-transfer capability through the reinforcement/matrix interface in composites reinforced by smaller particles.
引用
收藏
页码:643 / 649
页数:7
相关论文
共 44 条
[1]   DEFORMATION OF PLASTICALLY NON-HOMOGENEOUS MATERIALS [J].
ASHBY, MF .
PHILOSOPHICAL MAGAZINE, 1970, 21 (170) :399-&
[2]   Influences of pileup on the measurement of mechanical properties by load and depth sensing indentation techniques [J].
Bolshakov, A ;
Pharr, GM .
JOURNAL OF MATERIALS RESEARCH, 1998, 13 (04) :1049-1058
[3]  
CAHOON JR, 1971, METALL TRANS, V2, P1979
[4]   Structural phase transition in Al-Cu-Mg-Si alloys by transmission electron microscopy study on an Al-4 wt% Cu-1 wt% Mg-Ag alloy reinforced by SiC particles [J].
Cayron, C ;
Sagalowicz, L ;
Beffort, O ;
Buffat, PA .
PHILOSOPHICAL MAGAZINE A-PHYSICS OF CONDENSED MATTER STRUCTURE DEFECTS AND MECHANICAL PROPERTIES, 1999, 79 (11) :2833-2851
[5]   Influence of predeformation and ageing of an Al-Zn-Mg alloy - II. Modeling of precipitation kinetics and yield stress [J].
Deschamps, A ;
Brechet, Y .
ACTA MATERIALIA, 1998, 47 (01) :293-305
[6]  
Dieter G.E., 1986, MECH METALLURGY
[7]   An experimental and statistical study of interaction effects of matrix particle size, reinforcement particle size and volume fraction on the flexural strength of Al-SiCp composites by P/M using central composite design [J].
Diler, Ege Anil ;
Ipek, Rasim .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 548 :43-55
[8]   Decomposition of supersaturated solid solutions in Al-Cu-Mg-Si alloys [J].
Eskin, DG .
JOURNAL OF MATERIALS SCIENCE, 2003, 38 (02) :279-290
[9]   Precipitation processes in Al-Mg-Cu alloys [J].
Gouma, PI ;
Lloyd, DJ ;
Mills, MJ .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2001, 319 :439-442
[10]   Helium Implantation Effects on the Compressive Response of Cu Nanopillars [J].
Guo, Qiang ;
Landau, Peri ;
Hosemann, Peter ;
Wang, Yongqiang ;
Greer, Julia R. .
SMALL, 2013, 9 (05) :691-696