EXPERIMENTAL MEASUREMENTS AND FLOW VISUALIZATION OF WATER CAVITATION THROUGH A NOZZLE

被引:0
|
作者
Wilms, Jeffrey [1 ]
Beck, Terry [1 ]
Sorensen, Christopher M. [2 ]
Hosni, Mohammad H. [1 ]
Eckels, Steven J. [1 ]
Tomasi, Don [3 ]
机构
[1] Kansas State Univ, Mech & Nucl Engn Dept, Manhattan, KS 66506 USA
[2] Kansas State Univ, Dept Phys, Manhattan, KS 66506 USA
[3] D&V Consulting LLC, Stevensville, MI USA
来源
PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2014, VOL 7 | 2015年
关键词
Cavitation; Flow visualization; Vapor; Bubbles; Velocity;
D O I
暂无
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
typical refrigeration loop is composed of an evaporator, compressor, condenser, and an expansion valve. There are many possible refrigerants that can be used, but the physical properties. of water make it ineffective in the traditional refrigeration loop. But if water could be used it would have many advantages as it is abundant, cheap, and is safe for the environment. As part of development of a new refrigeration loop using water, flow visualization and cavitation of water through nozzles are being investigated. Cavitation is generally defined as creating vapor from liquid, not through adding heat, but by decreasing the pressure. In a converging/diverging nozzle as the cross sectional area is constricted the velocity of the flow will increase, decreasing the pressure. Therefore, by flowing water through the nozzle it will cavitate. Transforming liquid into gas requires a certain amount of energy, defined as the latent heat. When a liquid is turned to vapor by an increase in the temperature the latent heat is provided by the heat transfer to the system. As no energy is being added in the nozzle to cause the cavitation, the heat to create the vapor comes from the liquid, effectively causes a temperature drop. This article presents results for the flow visualization of the water cavitating as it goes through the nozzle. Under different flow conditions and nozzle geometries the cavitation manifested itself in different formations. When gasses were entrained in the water they formed bubbles, creating a nucleation site and moving through the nozzle, called travelling bubble cavitation. In venturi nozzles the cavitation nucleated off of the wall, formiong attached wall cavitation. When water flowed out of an orifice, a turbulent water jet was formed which caused vapor to form around it, causing shear cavitation. When the water was rotated prior to the throat of an orifice, the orifice jet expanded radially and formed swirl cavitation.
引用
收藏
页数:10
相关论文
共 50 条
  • [1] DIRECT PRESSURE MEASUREMENT AND FLOW VISUALIZATION OF CAVITATION IN A CONVERGING-DIVERGING NOZZLE
    Gallman, Benjamin
    Beck, B. Terry
    Hosni, Mohammad H.
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2019, VOL 7, 2020,
  • [2] CAVITATION MEASUREMENTS AND FLOW VISUALIZATION ON A HYDROFOIL WITH DIFFERENT TIP GAPS
    Deniz, Sabri
    PROCEEDINGS OF ASME TURBO EXPO 2024: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, GT2024, VOL 12C, 2024,
  • [3] High-Speed Cavitation Nozzle Flow Visualization of Liquid Jets
    Abderrezzak, Belkacem
    Huang, Yong
    2015 INTERNATIONAL CONFERENCE ON INFORMATION SCIENCE AND INTELLIGENT CONTROL (ISIC 2015), 2015, : 390 - 397
  • [4] THE EFFECT OF TEMPERATURE ON WATER CAVITATION PHENOMENA IN CONVERGING-DIVERGING NOZZLE FLOW
    Ahmed, Zayed
    Beck, B. Terry
    Hosni, Mohammad H.
    PROCEEDINGS OF THE ASME FLUIDS ENGINEERING DIVISION SUMMER MEETING, 2017, VOL 2, 2017,
  • [5] Visualization analysis of relationship between vortex flow and cavitation behavior in diesel nozzle
    Watanabe, Hiroki
    Nishikori, Masataka
    Hayashi, Tomohiro
    Suzuki, Masayuki
    Kakehashi, Nobuhisa
    Ikemoto, Masato
    INTERNATIONAL JOURNAL OF ENGINE RESEARCH, 2015, 16 (01) : 5 - 12
  • [6] Experimental analysis of cavitation in a centrifugal pump using acoustic emission, vibration measurements and flow visualization
    Mousmoulis, Georgios
    Karlsen-Davies, Nilla
    Aggidis, George
    Anagnostopoulos, Ioannis
    Papantonis, Dimitrios
    EUROPEAN JOURNAL OF MECHANICS B-FLUIDS, 2019, 75 : 300 - 311
  • [7] EXPERIMENTAL AND NUMERICAL STUDY ON THE EFFECTS OF NOZZLE GEOMETRY FEATURES ON THE NOZZLE INTERNAL FLOW AND CAVITATION CHARACTERISTICS
    Zhao, Wenbo
    Li, Zhilong
    Deng, Jun
    Li, Liguang
    Wu, Zhijun
    ATOMIZATION AND SPRAYS, 2021, 31 (06) : 67 - 95
  • [8] Cavitation analysis in a re-designed direct acting pressure relief valve through flow visualization method
    Sharma, Anubhav Kumar
    Kumar, Niranjan
    Das, Alok Kumar
    JOURNAL OF VISUALIZATION, 2023, 26 (06) : 1299 - 1319
  • [9] EXPERIMENTAL CHARACTERIZATION OF THE FLOW INSTABILITIES OF A MIXED-FLOW MULTIPHASE PUMP OPERATING AIR AND WATER THROUGH LOCAL VISUALIZATION AND ANALYSIS OF DYNAMIC MEASUREMENTS
    Serena, Alberto
    Bakken, Lars E.
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2015, VOL 7B, 2016,
  • [10] Effect of nozzle size scaling in co-flow water cavitation jet peening
    Marcon, Andrea
    Melkote, Shreyes N.
    Yoda, Minami
    JOURNAL OF MANUFACTURING PROCESSES, 2018, 31 : 372 - 381