Significant improvement in mechanical properties of Mg-Zn-La alloy by minor Ca addition

被引：18
|
作者：
Wang, Xin [1 ]
Du, Yuzhou [1 ,2 ]
Liu, Dongjie [1 ,2 ]
Jiang, Bailing [1 ,2 ]
机构：
[1] Xian Univ Technol, Sch Mat Sci & Technol, Xian 710048, Peoples R China
[2] Xian Univ Technol, Shaanxi Prov Engn Res Ctr Magnesium Alloys, Xian 710048, Peoples R China
来源：
MATERIALS CHARACTERIZATION | 2020年 / 160卷
基金：
中国国家自然科学基金;
关键词：
Mg-Zn-La; Dynamic recrystallization; Texture; Precipitates; Mechanical properties; DEFORMATION-BEHAVIOR; MAGNESIUM ALLOY; YIELD STRENGTH; MICROSTRUCTURE; TEXTURE; PARAMETERS; EVOLUTION; CERIUM;
D O I：
10.1016/j.matchar.2020.110130
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The microstructure and mechanical properties of a Mg-Zn-La alloy with and without Ca were investigated in the present study. Results indicated that small addition of Ca in Mg-Zn-La alloy induced the formation of Ca2Mg6Zn3 phase distributing at grain boundaries in the as-cast state and promoted dynamic precipitation in the as-extruded state. The existence of fine precipitates postponed dynamic recrystallization and refined dynamically recrystallized (DRXed) grains for Ca containing alloy. However, small addition of Ca did not affect the texture of the as-extruded Mg-Zn-La alloy obviously. The yield strength was increased by 70% after minor Ca addition from 141 MPa of the as-extruded Mg-Zn-La alloy to 241 MPa of the as-extruded Mg-Zn-La-Ca alloy. The significant increase of strength was mainly ascribed to refined microstructure and dynamic precipitates.
引用
收藏
页数：7
相关论文
共 50 条
  • [41] Microstructure and mechanical properties of Mg-4.0Zn-0.5Ca alloy
    Geng, L.
    Zhang, B. P.
    Li, A. B.
    Dong, C. C.
    MATERIALS LETTERS, 2009, 63 (05) : 557 - 559
  • [42] Mechanical and Biological Properties of a Biodegradable Mg-Zn-Ca Porous Alloy
    Zhang, Yong-qiang
    Li, Yang
    Liu, Huan
    Bai, Jing
    Bao, Ni-rong
    Zhang, Yue
    He, Peng
    Zhao, Jian-ning
    Tao, Li
    Xue, Feng
    Zhou, Guang-xin
    Fan, Gen-tao
    ORTHOPAEDIC SURGERY, 2018, 10 (02) : 160 - 168
  • [43] ISOTHERMAL SECTION OF Mg-Zn-La SYSTEM IN Mg RICH CORNER AT 350℃
    M.L. Huang
    Acta Metallurgica Sinica(English Letters), 2008, (05) : 329 - 335
  • [44] Effect of Zn and Cu Addition on Mechanical Properties of As-Extruded Mg-3Sn-1Ca Alloy
    Jia, Zheng
    Yu, Bing
    Fu, Li
    MATERIALS, 2022, 15 (13)
  • [45] Improvement of mechanical properties and reduction of yield asymmetry of extruded Mg-Al-Zn alloy through Sn addition
    Park, Sung Hyuk (sh.park@knu.ac.kr), 1600, Elsevier Ltd (766):
  • [46] Effects of Zn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg-2Al-0.5Ca Alloy
    Yuan, Ming
    He, Chao
    Song, Yan
    Lei, Bin
    Qian, Xiaoying
    Dong, Zhihua
    Zhao, Jun
    Yang, Huabao
    Chai, Yanfu
    Jiang, Bin
    Pan, Fusheng
    METALS, 2022, 12 (02)
  • [47] The improved mechanical properties of Mg-Zn-Nd alloy with Ca addition via grain refinement and nano precipitates
    Qian, Xiaoying
    Dong, Zhihua
    Jiang, Bin
    Zhang, Ang
    Wang, Cuihong
    Zheng, Zhiying
    Pan, Fusheng
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2023, 887
  • [48] Effects of zirconium addition on electrochemical and mechanical properties of Mg-3Zn-1Ca-1RE alloy
    Mousavian, Seyed Mohammad Hossein
    Tabaian, Seyed Hadi
    Badihehaghdam, Mohammadhassan
    ANTI-CORROSION METHODS AND MATERIALS, 2020, 67 (06) : 583 - 591
  • [49] Effects of Ca addition on the microstructures and mechanical properties of Mg-5Al-0.4Zn based casting alloy
    Yang, GY
    Hao, QT
    Ji, WQ
    Jia, WP
    He, Z
    ACTA METALLURGICA SINICA, 2005, 41 (09) : 933 - 939
  • [50] Effects of Zn and Ca addition on microstructure and mechanical properties of as-extruded Mg-1.0Sn alloy sheet
    Chai, Yanfu
    Jiang, Bin
    Song, Jiangfeng
    Liu, Bo
    Huang, Guangsheng
    Zhang, Dingfei
    Pan, Fusheng
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 746 (82-93): : 82 - 93
12345