Dissimilar friction stir welding between polycarbonate and AA 7075 aluminum alloy

被引：51

作者：

Moshwan, Raza ^{[1
,2
]}

Rahmat, Sahifulddin M. ^{[1
,2
]}

Yusof, Farazila ^{[1
,2
]}

Hassan, Mohsen A. ^{[1
,2
,3
]}

Hamdi, Mohd ^{[1
,2
]}

Fadzil, Mohd ^{[1
,2
]}

机构：

[1] Univ Malaya, Fac Engn, Dept Mech Engn, Kuala Lumpur 50603, Malaysia

[2] Univ Malaya, AMMP Ctr, Ctr Adv Mfg & Mat Proc, Kuala Lumpur 50603, Malaysia

[3] Assiut Univ, Dept Mech Engn, Assiut, Egypt

来源：

INTERNATIONAL JOURNAL OF MATERIALS RESEARCH | 2015年 / 106卷 / 03期

关键词：

Friction stir welding; AA; 7075; Polycarbonate; Mechanical interlocking; MECHANICAL-PROPERTIES; LAP JOINTS; PARAMETERS; TITANIUM; STEEL; MICROSTRUCTURE; STRENGTH; AL; EVOLUTION; POLYMERS;

D O I：

10.3139/146.111172

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

In this paper, the effects of process parameters, such as the tool rotational and traverse speeds, on temperature evolution and the microstructural and mechanical properties of dissimilar friction stir welding between 3 mm thick AA 7075 aluminum alloy and polycarbonate (PC) plates were investigated. The tool rotational and traverse speeds were varied from 3 000 to 3 500 rpm and 50 to 150 mm min(-1), respectively. The joint fabricated at 3 250 rpm and 100 mm min(-1) yielded a highest tensile load of 586 N. Microstructural analysis of the stir zone revealed an interlock phenomenon, the transportation of AA 7075 in polycarbonate, and the absence of ceramic-type (carbide, hydride or oxide) compounds. Microhardness (HV) measurement on the weld zone showed an uneven distribution due to the complicated microstructure of the welded joint. The maximum temperatures of 164 degrees C and 66 degrees C were obtained at 3 250 rpm and 100 mm min(-1) at a distance of 5 mm away from the welding centerline in the AA 7075 and PC side, respectively.

引用

页码：258 / 266

页数：9

共 50 条

[21] EFFECT OF TOOL PIN PROFILE ON FRICTION STIR WELDING OF DISSIMILAR MATERIALS AA5083 AND AA7075 ALUMINIUM ALLOY
AZMI, M. H.
HASNOL, M. Z.
ZAHARUDDIN, M. F. A.
SHARIF, S.
RHEE, S.
ARCHIVES OF METALLURGY AND MATERIALS, 2022, 67 (02) : 465 - 470
[22] Corrosion in friction stir welded dissimilar aluminum alloy joints of 2024 and 7075
Widener, Christian A.
Talia, Jorge E.
Tweedy, Bryan M.
Burford, Dwight A.
FRICTION STIR WELDING AND PROCESSING IV, 2007, : 449 - +
[23] Optimization and mechanical characterization of aa5083 and aa7075 dissimilar aluminium alloy joints produced by friction stir welding
Rajeshkannan S.
Vigneshkumar M.
Gopal V.
Ramesh S.
International Journal of Vehicle Structures and Systems, 2021, 13 (03) : 335 - 340
[24] Dissimilar friction stir welding between magnesium and aluminum alloys
Kwon, Y. J.
Shigematsu, I.
Saito, N.
MATERIALS LETTERS, 2008, 62 (23) : 3827 - 3829
[25] Underwater dissimilar friction stir lap welding of aluminum alloy and CFRTP
Zhang, Yuan
Sun, Yibo
Liu, Yong
Guan, Kainan
Wei, Xiao
Yang, Xinhua
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2024,
[26] Friction Stir Welding of T Joints of Dissimilar Aluminum Alloy: A Review
Thakare, Shrikant B.
Kalyankar, Vivek D.
ADVANCES IN MECHANICAL DESIGN, MATERIALS AND MANUFACTURE, 2018, 1943
[27] Crystal orientation evolution of friction stir welding of 2024/7075 dissimilar aluminum alloys
Zhou, Jun
Zhang, Jin
Ji, Pengfei
Hanjie Xuebao/Transactions of the China Welding Institution, 2016, 37 (08): : 59 - 62
[28] CDRX modelling in friction stir welding of AA7075-T6 aluminum alloy: Analytical approaches
Buffa, G.
Fratini, L.
Shivpuri, R.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 191 (1-3) : 356 - 359
[29] Dissimilar friction stir welding between 5052 aluminum alloy and AZ31 magnesium alloy
鄢勇
张大童
邱诚
张文
Transactions of Nonferrous Metals Society of China, 2010, 20(S2) (S2) : 619 - 623
[30] Dissimilar friction stir welding between 5052 aluminum alloy and AZ31 magnesium alloy
Yan Yong
Zhang Da-tong
Qiu Cheng
Zhang Wen
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2010, 20 : S619 - S623

← 1 2 3 4 5 →