Deformation behavior of an Al-Cu-Mg-Mn-Zr alloy during hot compression

被引：51

作者：

Li, Yao ^{[1
,2
]}

Liu, Zhiyi ^{[1
,2
]}

Lin, Lianghua ^{[1
,2
]}

Peng, Jiangtao ^{[1
,2
]}

Ning, Ailin ^{[3
]}

机构：

[1] Cent S Univ, Minist Educ, Key Lab Nonferrous Met Mat Sci & Engn, Changsha 410083, Peoples R China

[2] Cent S Univ, Sch Mat Sci & Engn, Changsha 410083, Peoples R China

[3] Shaoyang Univ, Dept Mech & Energy Engn, Shaoyang 422004, Peoples R China

来源：

JOURNAL OF MATERIALS SCIENCE | 2011年 / 46卷 / 11期

关键词：

PROCESSING MAPS; MICROSTRUCTURAL EVOLUTION; PRECIPITATION;

D O I：

10.1007/s10853-010-5143-7

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Deformation behavior of an Al-Cu-Mg-Mn-Zr alloy during hot compression was characterized in present work by high-temperature testing and transmission electron microscope (TEM) studies. The true stress-true strain curves exhibited a peak stress at a critical stain. The peak stress decreased with increasing deformation temperature and decreasing strain rate, which can be described by Zener-Hollomon (Z) parameter in hyperbolic sine function with the deformation activation energy 277.8 kJ/mol. The processing map revealed the existence of an optimum hot-working regime between 390 and 420 A degrees C, under strain rates ranging from 0.1 to 1 s(-1). The main softening mechanism of the alloy was dynamic recovery at high lnZ value; continuous dynamic recrystallization (DRX) occurred as deformed at low lnZ value. The dynamic precipitation of Al3Zr and Al20Cu2Mn3 dispersoids during hot deformation restrained DRX and increased the hot deformation activation energy of the alloy.

引用

页码：3708 / 3715

页数：8

共 30 条

[1] Hot deformation and processing maps of extruded ZE41A magnesium alloy [J].

Anbuselvan, S. ;

Ramanathan, S. .

MATERIALS & DESIGN, 2010, 31 (05) :2319-2323

[2] High temperature deformation behavior of Al-Cu-Mg alloys micro-alloyed with Sn [J].

Banerjee, Sanjib ;

Robi, P. S. ;

Srinivasan, A. ;

Kumar, Lakavath Praveen .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (10-11) :2498-2503

[3] Microstructural characterization of secondary-phase particles in a hot-deformed Al-Cu-Mg-Zr alloy [J].

Cabibbo, M ;

Evangelista, E ;

Spigarelli, S .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2004, 35A (01) :293-300

[4] Characterization of hot deformation behavior of a Ni-base superalloy using processing map [J].

Cai Dayong ;

Xiong Liangyin ;

Liu Wenchang ;

Sun Guidong ;

Yao Mei .

MATERIALS & DESIGN, 2009, 30 (03) :921-925

[5]

Castillo LD, 2000, METALL MATER TRANS A, V31, P2287

[6]

Cavaliere P., 2002, Journal of Light Metals, V2, P247

[7] Construction of processing map for biomedical Co-28Cr-6Mo-0.16N alloy by studying its hot deformation behavior using compression tests [J].

Chiba, Akihiko ;

Lee, Sang-Hak ;

Matsumoto, Hiroaki ;

Nakamura, Mitsuru .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 513-14 :286-293

[8] Deformation behavior of spray-formed hypereutectic Al-Si alloys [J].

Cui, C. ;

Schulz, A. ;

Epp, J. ;

Zoch, H. W. .

JOURNAL OF MATERIALS SCIENCE, 2010, 45 (10) :2798-2807

[9] The effect of heat treatment on hot deformation behaviour of Al 2024 [J].

Ebrahimi, G. R. ;

Zarei-Hanzaki, A. ;

Haghshenas, M. ;

Arabshahi, H. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 206 (1-3) :25-29

[10] Hot deformation of AA6082-T4 aluminum alloy [J].

El-Danaf, Ehab A. ;

AlMajid, Abdulhakim A. ;

Soliman, Mahmoud S. .

JOURNAL OF MATERIALS SCIENCE, 2008, 43 (18) :6324-6330

← 1 2 3 →