Expanded Lever Rule for Phase Volume Fraction Calculation of High-Strength Low-Alloy Steel in Thermal Simulation

被引：9

作者：

Lei, Xuanwei ^{[1
]}

Huang, Jihua ^{[1
]}

Chen, Shuhai ^{[1
]}

Zhao, Xingke ^{[1
]}

机构：

[1] Univ Sci & Technol Beijing, Sch Mat Sci & Engn, Beijing 100083, Peoples R China

来源：

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE | 2016年 / 47A卷 / 06期

关键词：

AUSTENITE-FERRITE TRANSFORMATION; C ALLOY; KINETICS; BAINITE; MODEL;

D O I：

10.1007/s11661-016-3410-1

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The principle of the lever rule on the dilatation curve and its application to the corresponding differential dilatation curve were introduced in a nonoverlapped two-phase continuous cooling process. The lever rule was further expanded in the case of an overlapped two-phase process. The application of the expanded lever rule was based on the approximate symmetry treatment on the differential dilatation curve, which shows reasonably both on the theoretical calculation and in the experimental results. High-strength low-alloy steels were thermal simulated with Gleeble 3500. The transformed phase volume fractions in different cooling processes were calculated by the expanded lever rule and metallography analysis. The results showed the expanded lever rule could calculate reliable phase volume fractions as metallography analysis. (C) The Minerals, Metals & Materials Society and ASM International 2016

引用

页码：2795 / 2803

页数：9

共 50 条

[21] Effect of Nb Addition and Heat Input on Heat-Affected Zone Softening in High-Strength Low-Alloy Steel [J].

Wang, Feilong ;

Zhao, Gang ;

Hou, Yu ;

Lin, Junpin ;

Li, Ba ;

Jia, Shujun ;

Liu, Qingyou ;

Liu, Gang ;

Yang, Ping .

MATERIALS, 2022, 15 (13)

[22] Structure and Properties of High-Strength Low-Alloy Cold-Resistant Steel after Reheat and Direct Quenching with Tempering [J].

Sych O.V. ;

Khlusova E.I. ;

Yashina E.A. ;

Svyatysheva E.V. ;

Vasilieva E.A. .

Inorganic Materials: Applied Research, 2020, 11 (06) :1299-1306

[23] Hot Deformation Behavior and Dynamic Recrystallization Characteristics in a Low-Alloy High-Strength Ni-Cr-Mo-V Steel [J].

Wu, Chuan ;

Han, Shuang .

ACTA METALLURGICA SINICA-ENGLISH LETTERS, 2018, 31 (09) :963-974

[24] Interdendritic microsegregation development of high-strength low-alloy steels during continuous casting process [J].

Zhang, Dayue ;

Strangwood, Martin .

MATERIALS SCIENCE AND TECHNOLOGY, 2019, 35 (11) :1337-1346

[25] Experimental and numerical analysis of micromechanical damage in the punching process for High-Strength Low-Alloy steels [J].

Achouri, Mohamed ;

Germain, Guenael ;

Dal Santo, Philippe ;

Saidane, Delphine .

MATERIALS & DESIGN, 2014, 56 :657-670

[26] Dilatometric and Microstructural Investigations on Austenite Decomposition under Continuous Cooling Conditions in a Cu-Bearing High-Strength Low-Alloy Steel [J].

Kumar, Atul ;

Sahoo, Lambodar ;

Kumar, Deepak ;

Singh, Vajinder ;

Gopinath, K. ;

Balamuralikrishnan, R. .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2022, 31 (11) :9060-9072

[27] Ferrite Grain Size Distributions in Ultra-Fine-Grained High-Strength Low-Alloy Steel After Controlled Thermomechanical Deformation [J].

S. Patra ;

S. Roy ;

Vinod Kumar ;

A. Haldar ;

D. Chakrabarti .

Metallurgical and Materials Transactions A, 2011, 42 :2575-2590

[28] Influence of Ti on non-metallic inclusion formation and acicular ferrite nucleation in high-strength low-alloy steel weld metals [J].

Kang, Yongjoon ;

Jang, Jihun ;

Park, Joo Hyun ;

Lee, Changhee .

METALS AND MATERIALS INTERNATIONAL, 2014, 20 (01) :119-127

[29] Effect of hot rolling process parameters on the microstructure and mechanical properties of continuously cooled low-carbon high-strength low-alloy (HSLA) steel [J].

Kucukakarsu, Furkan Yilmaz ;

Ayhan, Ismail Irfan ;

Alan, Emre ;

Tastemur, Demet ;

Gunduz, Suleyman .

MATERIALS TESTING, 2022, 64 (08) :1136-1149

[30] Lengthening kinetics of ferrite plates in high-strength low-carbon low alloy steel [J].

Wan, X. L. ;

Wei, R. ;

Cheng, L. ;

Enomoto, M. ;

Adachi, Y. .

JOURNAL OF MATERIALS SCIENCE, 2013, 48 (12) :4345-4355

← 1 2 3 4 5 →