Control of aluminum phosphate coating on mullite fibers by surface modification with polyethylenimine

被引：19

作者：

Chen, Chao ^{[1
]}

Feng, Bo ^{[1
]}

Hu, Shujuan ^{[1
]}

Zhang, Yue ^{[1
]}

Li, Song ^{[2
]}

Gao, Longfei ^{[2
]}

Zhang, Xuemei ^{[2
]}

Yu, Kun ^{[2
]}

机构：

[1] Beihang Univ, Sch Mat Sci & Engn, Minist Educ, Key Lab Aerosp Adv Mat & Performance, Beijing 100191, Peoples R China

[2] Beijing Composite Mat Co Ltd, State Key Lab Adv Fiber Composites, Beijing 102101, Peoples R China

来源：

CERAMICS INTERNATIONAL | 2018年 / 44卷 / 01期

关键词：

Ceramic-matrix composites; AlPO4; coating; Electrostatic attraction; Phase transformation; WOVEN CERAMIC FIBERS; FIBER/MULLITE MATRIX COMPOSITES; SOL-GEL PROCESS; MECHANICAL-PROPERTIES; OXIDE COMPOSITES; PRECIPITATION; INTERFACE; ALPO4; MONAZITE; INTERPHASE;

D O I：

10.1016/j.ceramint.2017.09.161

中图分类号：

TQ174 [陶瓷工业]; TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Aluminum phosphate (AIPO(4)) is a promising oxidation-resistant and weak interface for ceramic-matrix composites. In this research, AIPO(4) coating was deposited on mullite fibers by an improved liquid-phase method based on electrostatic attraction. A cationic polyelectrolyte, polyethylenimine (PEI), was used for surface modification of mullite fibers. The formation process, phase evolution and microstructure of the coating were studied. The zeta potential of AIPO(4) particles, PEI-adsorbed AIPO(4) particles, and PEI-adsorbed mullite particles was characterized to find the proper pH value for improving electrostatic attraction. The obtained AIPO(4) coating was porous and continuous, whose thickness could be controlled by multiple coating cycles. The relatively low calcination temperature (600 or 1000 degrees C) was a useful heat treatment method to develop bonding between coating and fiber as well as reduce the fiber strength degradation. The phase transformations of A1PO4 have little volume change, and cristobalite AIPO(4) is thermal compatible with mullite. Therefore, the coating structure was preserved after calcining at 1200 degrees C. The technique is also applicable for other fibers contained mullite phase to fabricate high-performance AIPO(4) coated mullite/mullite composites.

引用

页码：216 / 224

页数：9

共 52 条

[21]

Kamemizu H., 1987, J JPN DENT MAT, V6, P241

[22] Aluminosilicate fiber/mullite matrix composites with favorable high-temperature properties [J].

Kanka, B ;

Schneider, H .

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2000, 20 (05) :619-623

[23]

Kerans RJ, 2002, J AM CERAM SOC, V85, P2599, DOI 10.1111/j.1151-2916.2002.tb00505.x

[24] Nanostructural effect of AlPO4-nanoparticle coating on the cycle-life performance in LiCoO2 thin films [J].

Kim, Byoungsoo ;

Kim, Chunjoong ;

Ahn, Donggi ;

Moon, Taeho ;

Ahn, Jiwoo ;

Park, Yejun ;

Park, Byungwoo .

ELECTROCHEMICAL AND SOLID STATE LETTERS, 2007, 10 (02) :A32-A35

[25] Mullite-aluminum phosphate laminated composite fabricated by tape casting [J].

Kim, DK ;

Kriven, WM .

JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2003, 86 (11) :1962-1964

[26] Oxide laminated composites with aluminum phosphate (AlPO4) and alumina platelets as crack deflecting materials [J].

Kim, Dong-Kyu ;

Kriven, Waltraud M. .

COMPOSITES PART B-ENGINEERING, 2006, 37 (06) :509-514

[27] Nonaqueous Atomic Layer Deposition of Aluminum Phosphate [J].

Knohl, Stefan ;

Roy, Amit K. ;

Lungwitz, Ralf ;

Spanle, Stefan ;

Mkler, Thomas ;

Nestler, Daisy J. ;

Wielage, Bernhard ;

Schulze, Steffen ;

Hietschold, Michael ;

Wulff, Harm ;

Heim, Christiane A. ;

Seide, Falko ;

Zahn, Dietrich R. T. ;

Goedelt, Werner A. .

ACS APPLIED MATERIALS & INTERFACES, 2013, 5 (13) :6161-6167

[28] Oxide CMCs: interphase synthesis and novel fibre development [J].

Lewis, MH ;

Tye, A ;

Butler, EG ;

Doleman, PA .

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2000, 20 (05) :639-644

[29]

Li C. C., 2016, J AM CERAM SOC, V100

[30]

MORALES JG, 1992, J COLLOID INTERF SCI, V151, P555, DOI 10.1016/0021-9797(92)90503-E

← 1 2 3 4 5 6 →