Morphology, microstructure, and hardness of titanium (Ti-6Al-4V) blocks deposited by wire-feed additive layer manufacturing (ALM)

被引：260
作者：
Brandl, Erhard [1 ]
Schoberth, Achim [1 ]
Leyens, Christoph [2 ]
机构：
[1] EADS Innovat Works Metall Technol & Surface Engn, D-81663 Munich, Germany
[2] Tech Univ Dresden, Inst Mat Sci, Chair Mat Technol, D-01062 Dresden, Germany
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2012年 / 532卷
关键词：
Light microscopy; Microstructure; Chemical composition; Hardness measurement; Titanium alloys; Additive layer manufacturing; POWER DIODE-LASER; MECHANICAL-PROPERTIES; PART I; METAL-DEPOSITION; BETA-PHASE; ALLOY; EVOLUTION; POWDER; BEHAVIOR; ORIGIN;
D O I：
10.1016/j.msea.2011.10.095
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
Additive layer manufacturing offers a potential for time and cost savings, especially for aerospace components made from costly titanium alloys. In this paper, the morphology, microstructure, chemical composition, and hardness of additive manufactured Ti-6Al-4V blocks are investigated and discussed. Blocks (7 beads wide, 7 layers high) were deposited using Ti-6Al-4V wire and a Nd:YAG laser. Two different sets of parameters are used and three different post heat treatment conditions (as-built, 600 degrees C/4 h, 1200 degrees C/2 h) are investigated. The experiments reveal elementary properties of additive manufactured Ti-6Al-4V material in correlation to process parameters and heat treatments, which are discussed comprehensively. (C) 2011 Elsevier B.V. All rights reserved.
引用
收藏
页码：295 / 307
页数：13
相关论文
共 86 条
  • [1] ACKELID U, 2009, P MAT SCI TECHN MS T
  • [2] Ader C., 2004, SFF Symposium, P26
  • [3] Phase transformations during cooling in α+β titanium alloys
    Ahmed, T
    Rack, HJ
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1998, 243 (1-2): : 206 - 211
  • [4] The Origin of Microstructural Diversity, Texture, and Mechanical Properties in Electron Beam Melted Ti-6Al-4V
    Al-Bermani, S. S.
    Blackmore, M. L.
    Zhang, W.
    Todd, I.
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2010, 41A (13): : 3422 - 3434
  • [5] Almeida P., 2010, SOLID FREEFORM FABRI, P25
  • [6] [Anonymous], 2010, MICROSTRUCTURAL MECH
  • [7] [Anonymous], MIL HDB TIT TIT ALL
  • [8] Wire based additive layer manufacturing: Comparison of microstructure and mechanical properties of Ti-6Al-4V components fabricated by laser-beam deposition and shaped metal deposition
    Baufeld, Bernd
    Brandl, Erhard
    van der Biest, Omer
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2011, 211 (06) : 1146 - 1158
  • [9] Texture and Crystal Orientation in Ti-6Al-4V Builds Fabricated by Shaped Metal Deposition
    Baufeld, Bernd
    Van der Biest, Omer
    Dillien, Steven
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2010, 41A (08): : 1917 - 1927
  • [10] Mechanical properties of Ti-6Al-4V specimens produced by shaped metal deposition
    Baufeld, Bernd
    van der Biest, Omer
    [J]. SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS, 2009, 10 (01)
123456789