An experimental investigation of temperature distribution in workpiece machined surface layer in turning

被引：6

作者：

Huang, Kun ^{[1
]}

Yang, Wenyu ^{[1
]}

Chen, Qilin ^{[1
]}

He, Shaojie ^{[1
]}

机构：

[1] Huazhong Univ Sci & Technol, Sch Mech Sci & Technol, State Key Lab Digital Mfg Equipment & Technol, Wuhan 430074, Peoples R China

来源：

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY | 2016年 / 85卷 / 5-8期

基金：

中国国家自然科学基金;

关键词：

Cutting temperature; Machined surface; PVD film; Turning; SMALL PARTICLES; CHIP; LEAD;

D O I：

10.1007/s00170-015-8016-z

中图分类号：

TP [自动化技术、计算机技术];

学科分类号：

0812 ;

摘要：

Cutting temperature in workpiece has significant effects on machined surface integrity, including residual stress formation, metallurgical alteration, and microstructural change of workpiece material. In order to investigate temperature distribution in workpiece machined surface layer in external turning, an experimental investigation is carried out using physical vapor deposition (PVD) film method. This method provides an access to study temperature distribution as a function of depth in workpiece in turning. Effects of cutting parameters (cutting speed, feed rate, and depth of cut) on temperature distribution have been studied in dry cutting. Wet cutting condition was also studied in this paper to investigate the effects of different proportions of emulsion in cutting fluid on temperature distribution. This experimental investigation provides a new insight into the temperature distribution in workpiece machined surface layer in turning and is essential to the further research of machined surface integrity.

引用

页码：1207 / 1215

页数：9

共 50 条

[31] Investigations of Transient Machined Workpiece Surface Temperature in High Speed Peripheral Milling Using Inverse Method
Liu, Zhanqiang
Zhang, Fan
Jiang, Fulin
HIGH SPEED MACHINING V, 2012, 723 : 14 - 19
[32] Turning of aluminum metal matrix composites: influence of the reinforcement and the cutting condition on the surface layer of the workpiece
Jan C. Aurich
Marco Zimmermann
Stefan Schindler
Paul Steinmann
Advances in Manufacturing, 2016, 4 : 225 - 236
[33] Turning of aluminum metal matrix composites: influence of the reinforcement and the cutting condition on the surface layer of the workpiece
Aurich, Jan C.
Zimmermann, Marco
Schindler, Stefan
Steinmann, Paul
ADVANCES IN MANUFACTURING, 2016, 4 (03) : 225 - 236
[34] Experimental investigation on variation of machined residual stresses by turning and grinding of hardened AISI 1053 steel
Martell, Joseph J.
Liu, C. Richard
Shi, Jing
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 74 (9-12): : 1381 - 1392
[35] Experimental investigation on variation of machined residual stresses by turning and grinding of hardened AISI 1053 steel
Shi, Jing, 1600, Springer London (74): : 9 - 12
[36] Experimental investigation on variation of machined residual stresses by turning and grinding of hardened AISI 1053 steel
Joseph J. Martell
C. Richard Liu
Jing Shi
The International Journal of Advanced Manufacturing Technology, 2014, 74 : 1381 - 1392
[37] EXPERIMENTAL INVESTIGATION OF TEMPERATURE DISTRIBUTION IN A HORIZONTAL LAYER OF FLUID HEATED FROM BELOW
SOMERSCALES, EF
DROPKIN, D
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 1966, 9 (11) : 1189 - +
[38] An experimental investigation on the effect of turning parameters on surface roughness
Thangavel, P.
Selladurai, V.
International Journal of Manufacturing Research, 2008, 3 (03) : 285 - 300
[39] INVESTIGATION OF A TOOL AND WORKPIECE MACHINED USING A NICKEL-NANOCOATED INSERT
Manoj, Sureshkumar
Gandhi, Veeramalai Chinnasamy Sathish
MATERIALI IN TEHNOLOGIJE, 2018, 52 (02): : 171 - 175
[40] Experimental investigation on workpiece surface characteristics in Electric Discharge Machining (EDM)
Ergün, Zafer Emre
Çoǧun, Can
Journal of the Faculty of Engineering and Architecture of Gazi University, 2006, 21 (03): : 427 - 441

← 1 2 3 4 5 →