Microstructure and mechanical properties of a Zn-0.5Cu alloy processed by high-pressure torsion

被引：39
作者：
Bednarczyk, Wiktor [1 ]
Kawalko, Jakub [2 ]
Watroba, Maria [1 ]
Gao, Nong [3 ]
Starink, Marco J. [3 ]
Bala, Piotr [1 ,2 ]
Langdon, Terence G. [3 ]
机构：
[1] AGH Univ Sci & Technol, Fac Met Engn & Ind Comp Sci, Al A Mickiewicza 30, PL-30059 Krakow, Poland
[2] AGH Univ Sci & Technol, Acad Ctr Mat & Nanotechnol, Al A Mickiewicza 30, PL-30059 Krakow, Poland
[3] Univ Southampton, Dept Mech Engn, Mat Res Grp, Southampton SO17 1BJ, Hants, England
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2020年 / 776卷
关键词：
Grain refinement; High-pressure torsion; Severe plastic deformation; Ultrafine grains; Zinc alloys; SEVERE PLASTIC-DEFORMATION; ROOM-TEMPERATURE SUPERPLASTICITY; ULTRAFINE-GRAINED MATERIALS; PURE METALS; DYNAMIC RECRYSTALLIZATION; ZN-22-PERCENT AL; TEXTURE ANALYSIS; EVOLUTION; REFINEMENT; BEHAVIOR;
D O I：
10.1016/j.msea.2020.139047
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The microstructure, texture and mechanical properties of a quasi-single-phase Zn-0.5Cu (wt. %) alloy processed by high-pressure torsion (HPT) for up to 10 turns were investigated using electron backscatter diffraction (EBSD), Vickers hardness measurements and uniaxial tensile tests. The results show that during torsional straining there is dynamic recrystallization, subgrain refinement, a dissolution of epsilon - Zn4Cu precipitates and solid-solution strengthening. Monotonic deformation develops a strong {0001}11 (2) over bar0 local texture instead of the characteristic basal fiber texture. Sharp texture and misorientation angles for all grain boundaries of <30 degrees causes significantly higher yield stress and ultimate tensile stress compared to processing of the alloy by equal-channel angular pressing.
引用
收藏
页数：9
相关论文
共 50 条
  • [21] Influence of strain rate on the characteristics of a magnesium alloy processed by high-pressure torsion
    Serre, Pauline
    Figueiredo, Roberto B.
    Gao, Nong
    Langdon, Terence G.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (10-11): : 3601 - 3608
  • [22] The Evolvement of Mechanical Properties and Microstructure of Commercial Aluminum Alloy 6061 via High-Pressure Torsion
    Nuphairode, Cheeranan Krutsuwan
    Mohamed, Intan Fadhlina
    Lamin, Fauziana
    Zamri, Wan Fathul Hakim Wan
    Omar, Mohd Zaidi
    Horita, Zenji
    [J]. JURNAL KEJURUTERAAN, 2020, 32 (03): : 175 - 182
  • [23] High-cycle fatigue behavior of Zn-22% Al alloy processed by high-pressure torsion
    Choi, In-Chul
    Yoo, Byung-Gil
    Kraft, Oliver
    Schwaiger, Ruth
    Seok, Moo-Young
    Kawasaki, Megumi
    Langdon, Terence G.
    Jang, Jae-Il
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 618 : 37 - 40
  • [24] Effect of Zn content on microstructure evolution in Al-Zn alloys processed by high-pressure torsion
    Ahmed, Anwar Q.
    Ugi, David
    Lendvai, Janos
    Murashkin, Maxim Yu.
    Bobruk, Elena V.
    Valiev, Ruslan Z.
    Chinh, Nguyen Q.
    [J]. JOURNAL OF MATERIALS RESEARCH, 2023, 38 (14) : 3602 - 3612
  • [25] Effect of annealing on mechanical properties of a nanocrystalline CoCrFeNiMn high-entropy alloy processed by high-pressure torsion
    Shahmir, Hamed
    He, Junyang
    Lu, Zhaoping
    Kawasaki, Megumi
    Langdon, Terence G.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 676 : 294 - 303
  • [26] Mechanical properties and microstructural evolution of high-pressure torsion-processed Al7075 alloy at elevated temperatures
    Oh, Juhee
    Park, Sangeun
    Bae, Hyo Ju
    Son, Sujung
    Kim, Hyoung Seop
    Seol, Jae Bok
    Sung, Hyokyung
    Kim, Jung Gi
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 835
  • [27] The effect of high-pressure torsion process on the microstructure and mechanical properties of Al-Zn-Mg-Cu alloy
    Jian, Song
    Feng, Dong
    Xue, Kemin
    Ding, Yonggen
    [J]. MATERIALS LETTERS, 2025, 387
  • [28] Effect of a minor titanium addition on the superplastic properties of a CoCrFeNiMn high-entropy alloy processed by high-pressure torsion
    Shahmir, Hamed
    Nili-Ahmadabadi, Mahmoud
    Shafiee, Ahad
    Langdon, Terence G.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 718 : 468 - 476
  • [29] A critical evaluation of microstructure-texture-mechanical behavior heterogeneity in high pressure torsion processed CoCuFeMnNi high entropy alloy
    Sonkusare, Reshma
    Biswas, Krishanu
    Al-Hamdany, Nowfal
    Brokmeier, H. G.
    Kalsar, R.
    Schell, Norbert
    Gurao, N. P.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 782
  • [30] Evidence for two-stage hardening in an Al-Zn-Mg-Cu alloy processed by high-pressure torsion
    dos Santos, Igor C.
    Mazzer, Eric M.
    Figueiredo, Roberto B.
    Langdon, Terence G.
    Pereira, Pedro Henrique R.
    [J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2023, 941
12345