INFLUENCE OF PLASTIC DEFORMATION DURING EXTRUSION PROCESS ON HEAT RESISTANCE ALLOYS Fe40Al

被引：1

作者：

Pasek, D. ^{[1
]}

Cebulski, J. ^{[1
]}

机构：

[1] Silesian Tech Univ, Dept Mat Engn & Met, 8 Krasinskiego Str, PL-40019 Katowice, Poland

来源：

ARCHIVES OF METALLURGY AND MATERIALS | 2017年 / 62卷 / 04期

关键词：

corrosion resistance; plastic deformation; alloys intermetallic phase matrix FeAl; Al2O3; extrusion; IRON ALUMINIDE; OXIDATION; MICROSTRUCTURE; FEAL;

D O I：

10.1515/amm-2017-0336

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

The article presents the results of studies on the effects wrought on the corrosion resistance of the alloy matrix phase intermetallic FeAl. Researches were carried out on the Fe40Al5Cr0.2TiB alloy and involved the oxidation of the samples after the crystallization after plastic deformation made by extrusion. The tests were performed in an oven in air at 1100 degrees C for 100, 300 and 500 h. Determined to change the mass of the samples after corrosion research setting kinetics of corrosion processes, as well as an analysis of the microstructure of the alloy after the crystallization and after forming. The structure was examined using light microscopy and scanning electron microscopy and X-ray microanalysis with EDS chemical composition of the corrosion products. The test results revealed that plastic deformation during extrusion of intermetallic alloy led to structural changes, the effect of which was to improve the heat resistance at a temperature of 1100 degrees C.

引用

收藏

页码：2281 / 2286

页数：6

相关论文

共 50 条

[41] Deformation mechanisms and mechanical properties of the high-strength and ductile Al-Zn-Mg-Cu alloys processed by repetitive continuous extrusion forming process with different heat treatments [J].

Wen, Chenyu ;

Tang, Jie ;

Chen, Wentian ;

Jiang, Fulin ;

Chen, Yonggang ;

Zhang, Hui ;

Teng, Jie .

JOURNAL OF ALLOYS AND COMPOUNDS, 2023, 965

[42] Optimization of Strength-Electrical Conductivity Properties in Al-2Fe Alloy by Severe Plastic Deformation and Heat Treatment [J].

Medvedev, Andrey E. ;

Murashkin, Maxim Y. ;

Enikeev, Nariman A. ;

Valiev, Ruslan Z. ;

Hodgson, Peter D. ;

Lapovok, Rimma .

ADVANCED ENGINEERING MATERIALS, 2018, 20 (03)

[43] COMPARISON OF HIGH TEMPERATURE CORROSION RESISTANCE IN GASEOUS ENVIRONMENT OF ALLOYS BASED ON INTERMETALLIC PHASE MATRIX Fe40Al5CrZrB AND STEEL X12CrCoNi2120 [J].

Cebulski, J. ;

Fornalczyk, A. ;

Pasek, D. .

ARCHIVES OF METALLURGY AND MATERIALS, 2014, 59 (02) :447-450

[44] A now deformation-semi-solid casting process of highly concentrated Fe containing Al-Si-Cu-Fe cast alloys [J].

Sato, Tatsuo ;

Tezuka, Hiroyasu .

SEMI- SOLID PROCESSING OF ALLOYS AND COMPOSITES, 2006, 116-117 :247-250

[45] Influence of aging treatment on plastic deformation and a-phase formation in Fe40Mn40Co10Cr10 medium entropy alloy [J].

Xu, T. R. ;

Ma, Y. J. ;

Wang, X. T. ;

Hu, Y. Y. ;

Cheng, J. ;

Hassanzai, H. H. ;

Song, X. Y. ;

Zhao, W. L. ;

Wu, S. ;

Jiao, M. H. ;

Cao, Z. H. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2025, 1036

[46] INFLUENCE OF A LOW-TEMPERATURE PLASTIC-DEFORMATION PROCESS ON THE MICROSTRUCTURE OF AN Al-Si-Mg ALUMINUM ALLOY [J].

Gode, Ceren .

MATERIALI IN TEHNOLOGIJE, 2021, 55 (02) :283-291

[47] The influence of hot deformation on the microstructure of Ni-Al and Ni-Al-Fe alloys with small Ti2B addition [J].

Czeppe, T ;

Szczepanik, S .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1996, 60 (1-4) :317-323

[48] Deformation-induced dissolution of copper precipitation in 1.5wt% Cu-bearing antibacterial Fe-17wt%Cr alloy during plastic deformation process [J].

Sun, Shaoheng ;

Yin, Fei ;

Liu, Yifei ;

Zhang, Wei ;

Zhao, Aimin ;

Han, Qingyou .

MATERIALS & DESIGN, 2018, 157 :469-477

[49] Pitting Resistance of Al90Fe7Nb3 and Al90Fe7Zr3 Nanocrystalline Alloys Obtained by Melt-Spinning and Hot Extrusion [J].

Rodrigues, C. A. D. ;

Kiminami, C. S. ;

Botta, W. J. ;

Tremiliosi-Filho, G. .

PORTUGALIAE ELECTROCHIMICA ACTA, 2009, 27 (03) :309-316

[50] Influence of Combined Severe Plastic Deformation and Sheet Extrusion Process on the Superplastic Formability of AA 5083 Aluminum Alloy Assessed by Free Bulge Test [J].

Fereshteh-Saniee, F. ;

Fakhar, N. ;

Mahmudi, R. .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2019, 28 (11) :6682-6691

← 1 2 3 4 5 →