Characterization of a powder metallurgy SiC/Cu-Al composite

被引：86

作者：

Wang, Hailong ^{[1
,2
]}

Zhang, Rui ^{[1
]}

Hu, Xing ^{[1
]}

Wang, Chang-An ^{[2
]}

Huan, Yong ^{[2
]}

机构：

[1] Zhengzhou Univ, Minist Educ China, Phys Mat Lab, Henan 450002, Peoples R China

[2] Tsinghua Univ, State Key Lab New Ceram & Fine Proc, Beijing 100084, Peoples R China

来源：

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 2008年 / 197卷 / 1-3期

关键词：

SiC/Cu-Al; composite; microstructure; density; powder metallurgy;

D O I：

10.1016/j.jmatprotec.2007.06.002

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

SiC particulate-reinforced Al composites were prepared by powder metallurgy (PM) method and conventional atmospheric sintering. Scanning electron microscope (SEM), X-ray diffraction (XRD) techniques were used to characterize the sintered composites. The effect of temperature on the density; hardness, strength, and microstructure of composites was investigated. Detailed failure behavior was analyzed. It was found that the segregation of Sic appeared at higher temperature. The highest micro-hardness of 80 MPa occurred at 700 degrees C. The strength tended to increase with the increasing temperature due to the formation of Al2Cu. Both ductile and brittle fracture features were observed. (C) 2007 Published by Elsevier B.V.

引用

页码：43 / 48

页数：6

共 27 条

[1]

Clyne T.W., 1993, INTRO METAL MATRIX C

[2] THE INFLUENCE OF PARTICLE DISTRIBUTION ON THE MECHANICAL RESPONSE OF A PARTICULATE METAL-MATRIX COMPOSITE [J].

CORBIN, SF ;

WILKINSON, DS .

ACTA METALLURGICA ET MATERIALIA, 1994, 42 (04) :1311-1318

[3]

DEGISCHER HP, 2001, EUROPEAN THERMATIC A, V32, P1161

[4] Structure and amorphization of the oxide on the silicon carbide surface in an SiCp Al composite [J].

Gu, MY ;

Mei, Z ;

Jin, YP ;

Wu, ZG .

SCRIPTA MATERIALIA, 1999, 40 (09) :985-991

[5] EFFECTS OF VACUUM HOT-PRESSING PARAMETERS ON THE TENSILE PROPERTIES AND MICROSTRUCTURES OF SIC-2124 AL COMPOSITES [J].

HONG, SH ;

CHUNG, KH .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1995, 194 (02) :165-170

[6] Effects of thermal processing on thermal expansion coefficient of a 50 vol.% SiCP/Al composite [J].

Kim, BG ;

Dong, SL ;

Park, SD .

MATERIALS CHEMISTRY AND PHYSICS, 2001, 72 (01) :42-47

[7] The fabrication process and mechanical properties of SiCp/Al-Si metal matrix composites for automobile air-conditioner compressor pistons [J].

Lee, HS ;

Yeo, JS ;

Hong, SH ;

Yoon, DJ ;

Na, KH .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2001, 113 (1-3) :202-208

[8] Statistical evaluation of strength for die-cast SiCp/Al alloy composites [J].

Lee, TW ;

Lee, CH .

MATERIALS LETTERS, 2000, 46 (2-3) :93-97

[9] The tribological properties of Al-Cu/SiCp metal-matrix composites fabricated using the rheocasting technique [J].

Lim, SC ;

Gupta, M ;

Ren, L ;

Kwok, JKM .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1999, 90 :591-596

[10] Fatigue crack tip opening behavior in particulate reinforced Al-alloy composites [J].

Liu, G ;

Shang, JK .

ACTA MATERIALIA, 1996, 44 (01) :79-91

← 1 2 3 →