Deposition rates on stainless steel substrates of different surface roughnesses under different operating conditions using thermal CVD

被引：2
作者：
Rahman, Md. Mostafizur [1 ]
Chowdhury, Mohammad Asaduzzaman [1 ]
Nuruzzaman, Dewan Muhammad [1 ]
Debnath, Uttam Kumar [1 ]
Kowser, Md. Arefin [1 ]
Roy, Biplov Kumar [1 ]
机构：
[1] Dhaka Univ Engn & Technol, Dept Mech Engn, Gazipur 1700, Bangladesh
来源：
INTERNATIONAL JOURNAL OF SURFACE SCIENCE AND ENGINEERING | 2016年 / 10卷 / 03期
关键词：
deposition rate; surface roughness; thermal CVD; stainless steels; friction coefficient; wear rate; CHEMICAL-VAPOR-DEPOSITION; GAS-FLOW RATE; OPTICAL-PROPERTIES; DIAMOND; GROWTH; NUCLEATION; TEMPERATURE; DEPENDENCE; KINETICS;
D O I：
10.1504/IJSURFSE.2016.076999
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
A series of experimental tests were carried out to observe the deposition rates on different stainless steel substrates of different surface roughnesses under different operating conditions using a hot filament thermal chemical vapour deposition (CVD) reactor. The test parameters include gas flow rate of methane, temperature of substrate and activation heaters, distance between activation heater and substrate, pressure and duration. There are significant effects of these parameters on deposition rate of different stainless steel materials. It was found that deposition rates strongly depend on different surface roughnesses of the stainless steel substrates under different tested conditions within the observed range. Tribological properties, especially friction and wear of these stainless steel materials sliding against SS 314 under different normal loads and sliding velocities are also investigated before and after deposition. The obtained results reveal that the values of friction and wear are lower after deposition than that of before deposition.
引用
收藏
页码：282 / 302
页数：21
相关论文
共 45 条
[31]   Experimental Study on Surface Roughness and Optimization of Process Parameters Using ANN-GA in Milling of Super-Duplex Stainless Steel Under Dry and Wet Conditions [J].
Sambedana, Soumya ;
Subhash, N. ;
Raj, P. Nithin ;
Jagadeesha, T. .
ADVANCES IN MANUFACTURING TECHNOLOGY, 2019, :399-409
[32]   Grinding behavior of VP50IM steel using green and black silicon carbide compared to aluminum oxide wheel under different feed rates [J].
da Silva, Andrigo Elisiario ;
Cuesta, Jorge Luiz ;
Lopes, Jose Claudio ;
de Moraes, Douglas Lyra ;
Garcia, Mateus Vinicius ;
Fonteque Ribeiro, Fernando Sabino ;
de Mello, Hamilton Jose ;
De Angelo Sanchez, Luiz Eduardo ;
Aguiar, Paulo Roberto ;
Bianchi, Eduardo Carlos .
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 117 (9-10) :2639-2653
[33]   Microstructures and Properties of Auto-Tempering Ultra-High Strength Automotive Steel under Different Thermal-Processing Conditions [J].
Jiang, Han ;
He, Yanlin ;
Lin, Li ;
Liu, Rendong ;
Zhang, Yu ;
Zheng, Weisen ;
Li, Lin .
METALS, 2021, 11 (07)
[34]   Effect of Ni and Cu catalysts on graphene growth under different ethanol flow rates using atmospheric pressure chemical vapor deposition [J].
Abdalrheem, Raed ;
Yam, F. K. ;
Ibrahim, Abdul Razak ;
Lim, H. S. ;
Beh, K. P. ;
Oglat, Ammar A. ;
Afzal, Naveed ;
Chahrour, Khaled M. ;
Mohammad, Sabah M. .
MATERIALS RESEARCH EXPRESS, 2019, 6 (08)
[35]   Kinetic model of the thermal pyrolysis of chrome tanned leather treated with NaOH under different conditions using thermogravimetric analysis [J].
Banon, E. ;
Marcilla, A. ;
Garcia, A. N. ;
Martinez, P. ;
Leon, M. .
WASTE MANAGEMENT, 2016, 48 :285-299
[36]   Effects of Secondary-Phase Formation on the Electrochemical Performance of a Wire Arc Additive Manufactured 420 Martensitic Stainless Steel under Different Heat Treatment Conditions [J].
Salahi, Salar ;
Ghaffari, Mahya ;
Nemani, Alireza Vahedi ;
Nasiri, Ali .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2021, 30 (09) :6618-6629
[37]   Effect of processing parameters and build orientation on microstructure and performance of AISI stainless steel 304L made with selective laser melting under different strain rates [J].
Pan, Tan ;
Zhang, Xinchang ;
Flood, Aaron ;
Karnati, Sreekar ;
Li, Wei ;
Newkirk, Joseph ;
Liou, Frank .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 835
[38]   THERMAL-HYDRAULIC ANALYSIS OF LIGHT WATER REACTORS UNDER DIFFERENT STEADY-STATE OPERATING CONDITIONS Part 2-Pressurized Water Reactor [J].
Hutli, Ezddin ;
Kridan, Ramadan .
NUCLEAR TECHNOLOGY & RADIATION PROTECTION, 2022, 37 (04) :276-288
[39]   Macro-micro mechanical properties of building sandstone under different thermal damage conditions and thermal stability evaluation using acoustic emission technology [J].
Liu, Zhen ;
Yao, Qingguo ;
Kong, Biao ;
Yin, Jueli .
CONSTRUCTION AND BUILDING MATERIALS, 2020, 246
[40]   Prediction of internal relative humidity of concrete under different thermal conditions using an enhanced long short-term memory network [J].
Fu, Wenwei ;
Sun, Bochao ;
Noguchi, Takafumi ;
Zhao, Weijian ;
Ye, Jun .
THERMAL SCIENCE AND ENGINEERING PROGRESS, 2023, 38
12345