Effect of extrusion and particle volume fraction on the mechanical properties of SiC reinforced Al-Cu alloy composites

被引：111

作者：

Wang, Zhangwei ^{[1
]}

Song, Min ^{[1
]}

Sun, Chao ^{[1
]}

Xiao, Daihong ^{[1
]}

He, Yuehui ^{[1
]}

机构：

[1] Cent S Univ, State Key Lab Powder Met, Changsha 410083, Peoples R China

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2010年 / 527卷 / 24-25期

基金：

中国国家自然科学基金;

关键词：

Aluminum matrix composites; Mechanical properties; Microstructure; Extrusion; METAL-MATRIX COMPOSITES; TENSILE BEHAVIOR; ALUMINUM; FRACTURE; SIZE; TEMPERATURES; DEFORMATION;

D O I：

10.1016/j.msea.2010.07.017

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

This paper studied the combined effects of extrusion and reinforcement volume fraction on the mechanical properties of SiC particles reinforced Al-Cu alloy composites. It has been shown that extrusion can improve the distributed homogeneity of the SiC particles in the matrix and enhance the interfacial bonding strength of the composites. The hardness of the composites increased with increasing the volume fraction of the SiC particles, while the yield strength and tensile strength of the composites decreased with increasing the volume fraction of the SiC particles due to the particle fracture during extrusion. It has also been shown that the hardness increased with the aging time until reaching the maximum values, after which the hardness started to decrease. Fracture surface observations showed that the dominant fracture mechanism of the composites is ductile fracture of the matrix, accompanied by the pull-out of the particles from the matrix before extrusion or by the SiC particle fracture after extrusion, respectively. (C) 2010 Elsevier B.V. All rights reserved.

引用

页码：6537 / 6542

页数：6

共 37 条

[1] Aging behavior of a 2024 Al alloy-SiCp composite [J].

Abarghouie, S. M. R. Mousavi ;

Reihani, S. M. Seyed .

MATERIALS & DESIGN, 2010, 31 (05) :2368-2374

[2] A COMPARISON OF PM VS MELTED SIC AL COMPOSITES [J].

ARSENAULT, RJ ;

WU, SB .

SCRIPTA METALLURGICA, 1988, 22 (06) :767-772

[3] DEGRADATION OF SIC PARTICLES IN ALUMINUM-BASED COMPOSITES [J].

CAROTENUTO, G ;

GALLO, A ;

NICOLAIS, L .

JOURNAL OF MATERIALS SCIENCE, 1994, 29 (19) :4967-4974

[4] Effect of SiC volume fraction and particle size on the fatigue resistance of a 2080 Al/SiCp composite [J].

Chawla, N ;

Andres, C ;

Jones, JW ;

Allison, JE .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1998, 29 (11) :2843-2854

[5]

Chawla N, 2001, ADV ENG MATER, V3, P357, DOI 10.1002/1527-2648(200106)3:6<357::AID-ADEM357>3.0.CO

[6]

2-I

[7]

CHAWLA N, 1998, MATER SCI ENG, V38, P1596

[8]

Clyne T.W., 1993, INTRO METAL MATRIX C

[9] LOW STRAIN PLASTICITY IN A PARTICULATE METAL-MATRIX COMPOSITE [J].

CORBIN, SF ;

WILKINSON, DS .

ACTA METALLURGICA ET MATERIALIA, 1994, 42 (04) :1319-1327

[10] RESIDUAL-STRESSES AND THEIR EFFECTS ON DEFORMATION IN PARTICLE-REINFORCED METAL-MATRIX COMPOSITES [J].

DAVIS, LC ;

ALLISON, JE .

METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1993, 24 (11) :2487-2496

← 1 2 3 4 →