Improvement in the r-value of aluminum sheets by differential-friction rolling

被引：44
|
作者：
Utsunomiya, H. [1 ]
Ueno, T. [1 ]
Sakai, T. [1 ]
机构：
[1] Osaka Univ, Grad Sch Engn, Div Mat & Mfg Sci, Osaka, Japan
来源：
SCRIPTA MATERIALIA | 2007年 / 57卷 / 12期
关键词：
asymmetric rolling; shear texture; lankford value; differential-speed rolling;
D O I：
10.1016/j.scriptamat.2007.08.024
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
Differential-speed rolling can improve the formability of aluminum alloys through the formation of shear texture. The authors propose an alternative asymmetric rolling method. The asymmetry is achieved by differentiating the friction on the upper interface from that on the lower interface. A commercial aluminum sheet in which one surface was coated with PTFE was rolled. The shear strain introduced was comparable to that introduced by differential-speed rolling. The annealed sheet showed a higher r-value than the symmetrically rolled sheet. (C) 2007 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
引用
收藏
页码：1109 / 1112
页数：4
相关论文
共 50 条
  • [31] The influence of cold rolling reduction on r-value and recrystallization behavior in Fe-36Ni alloy
    Sato, T
    Tashiro, Y
    Honda, Y
    Nishida, M
    Chiba, A
    ISIJ INTERNATIONAL, 1998, 38 (06) : 640 - 646
  • [32] ASSESSMENT OF DEEP DRAWABILITY OF COMMERCIALLY PURE TITANIUM SHEETS IN CONSIDERATION OF R-VALUE CHANGE DURING PROCESSING
    KAWAI, N
    HAYASHI, N
    TAKAYAMA, K
    JSME INTERNATIONAL JOURNAL, 1987, 30 (267) : 1487 - 1494
  • [33] Effect of hot-rolling processing on texture and r-value of annealed dual-phase steels
    Han, Seong-Ho
    Choi, Shi-Hoon
    Choi, Jae-Kwon
    Seong, Hwan-Goo
    Kim, In-Bae
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (7-8): : 1686 - 1694
  • [34] Effect of single and double cold-rolling reductions on the planar anisotropy of r-value in sheet steels
    Okuda, K
    Fujinaga, C
    Tosaka, A
    Furukimi, O
    Kuguminato, H
    TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2000, 86 (01): : 32 - 37
  • [35] Effect of Hot-rolling Conditions on Texture and R-value of 16%Cr Ferritic Stainless Steel
    Yokota, Takeshi
    Ujiro, Takumi
    Furukimi, Osamu
    TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2018, 104 (08): : 53 - 60
  • [36] Improvement of mechanical properties of 7475 based aluminum alloy sheets by controlled warm rolling
    Tanaka, H
    Esaki, H
    Yamada, K
    Shibue, K
    Yoshida, H
    MATERIALS TRANSACTIONS, 2004, 45 (01) : 69 - 74
  • [37] Development of hot-rolled steel sheet with a high r-value by rolling in ferrite region with lubrication
    Hashimoto, Shun-ichi
    Tsukatani, Ichiro
    Kashima, Takahiro
    Miyoshi, Tetsuji
    R and D: Research and Development Kobe Steel Engineering Reports, 1998, 48 (01): : 14 - 18
  • [38] ASSESSMENT OF DEEP-DRAWABILITY OF MILD-STEEL SHEETS IN CONSIDERATION OF R-VALUE CHANGE DURING PROCESSING
    KAWAI, N
    HAYASHI, N
    MATSUI, S
    JOURNAL OF ENGINEERING FOR INDUSTRY-TRANSACTIONS OF THE ASME, 1988, 110 (04): : 376 - 383
  • [39] Improvement of Settling Performance by Initial Value Compensation Considering Rolling Friction Characteristic
    Maeda, Yoshihiro
    Iwasaki, Makoto
    IECON 2010 - 36TH ANNUAL CONFERENCE ON IEEE INDUSTRIAL ELECTRONICS SOCIETY, 2010,
  • [40] Fatigue life improvement of similar and dissimilar aluminum friction stir welds by deep rolling
    Jan Schubnell
    Antonia Müller
    Ralf Boywitt
    Oliver Maiß
    Majid Farajian
    Welding in the World, 2023, 67 : 721 - 732
12345