Numerical analysis of a hermetic reciprocating compressor oil pump system

被引：11

作者：

Posch, S. ^{[1
]}

Hopfgartner, J. ^{[1
]}

Berger, E. ^{[1
]}

Zuber, B. ^{[1
]}

Schoellauf, P. ^{[2
]}

Almbauer, R. ^{[1
]}

机构：

[1] Graz Univ Technol, Inst Internal Combust Engines & Thermodynam, Inffeldgasse 19, A-8010 Graz, Austria

[2] Secop Austria GmbH, Jahnstr 30, A-8280 Furstenfeld, Austria

来源：

INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID | 2018年 / 85卷

关键词：

Hermetic reciprocating compressor; Oil pump; CFD; Modeling optimization; FLUID-FLOW;

D O I：

10.1016/j.ijrefrig.2017.09.017

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

The aim of this work is to present a method for the analysis of an oil supply pump system of a reciprocating compressor based on a split-up approach. The entire oil pump is therefore split-up into three separate pumps: two centrifugal pumps and one helical groove pump. The split-up approach allows optimizing each single part of the pump without calculating the entire system. Different numerical models such as the Volume of Fluid (VOF) method or single phase models are used for each pump. The simulations for each pump are carried out in ANSYS Fluent 15.0. Performance curves are calculated for each pump and combined to a performance curve of the entire oil pump. The simulation results are validated with experimental data of an oil pump test rig. Finally, the presented simulation strategy is compared qualitatively with a numerical simulation of the entire oil pump concerning accuracy and computational time. (C) 2017 Elsevier Ltd and IIR. All rights reserved.

引用

页码：135 / 143

页数：9

共 14 条

[1]

Alves M., 2012, INT COMPR ENG C PURD

[2] Fluid flow in a screw pump oil supply system for reciprocating compressors [J].

Alves, Marcus V. C. ;

Barbosa, Jader R., Jr. ;

Prata, Alvaro T. ;

Ribas, Fernando A., Jr. .

INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID, 2011, 34 (01) :74-83

[3] Analytical solution of single screw extrusion applicable to intermediate values of screw channel aspect ratio [J].

Alves, Marcus Vinicius C. ;

Barbosa, Jader R., Jr. ;

Prata, Alvaro T. .

JOURNAL OF FOOD ENGINEERING, 2009, 92 (02) :152-156

[4] SOLUTION OF THE IMPLICITLY DISCRETIZED FLUID-FLOW EQUATIONS BY OPERATOR-SPLITTING [J].

ISSA, RI .

JOURNAL OF COMPUTATIONAL PHYSICS, 1986, 62 (01) :40-65

[5] Investigation of oil flow in a hermetic reciprocating compressor [J].

Kerpicci, Husnu ;

Yagci, Alper ;

Onbasioglu, Seyhan U. .

INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID, 2013, 36 (01) :215-221

[6] Numerical study on the lubrication oil distribution in a refrigeration rotary compressor [J].

Kim, HJ ;

Lancey, TW .

INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID, 2003, 26 (07) :800-808

[7] Modeling of flow in a single screw extruder [J].

Li, Y ;

Hsieh, F .

JOURNAL OF FOOD ENGINEERING, 1996, 27 (04) :353-375

[8] Analysis of oil pumping in a reciprocating compressor [J].

Luckmann, Antonio J. ;

Alves, Marcus Vinicius C. ;

Barbosa, Jader R., Jr. .

APPLIED THERMAL ENGINEERING, 2009, 29 (14-15) :3118-3123

[9]

Moukalled F, 2015, The Finite Volume Method in Computational Fluid Dynamics: An Advanced Introduction with OpenFOAM and Matlab, DOI DOI 10.1007/978-3-319-16874-6

[10] CALCULATION PROCEDURE FOR HEAT, MASS AND MOMENTUM-TRANSFER IN 3-DIMENSIONAL PARABOLIC FLOWS [J].

PATANKAR, SV ;

SPALDING, DB .

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 1972, 15 (10) :1787-&

← 1 2 →