Microstructural characterization and evolution mechanism of adiabatic shear band in a near beta-Ti alloy

被引：87
作者：
Yang, Y. [1 ,2 ]
Jiang, F. [1 ]
Zhou, B. M. [1 ]
Li, X. M. [1 ]
Zheng, H. G. [1 ]
Zhang, Q. M. [2 ]
机构：
[1] Cent S Univ, Sch Mat Sci & Engn, Changsha 410083, Hunan, Peoples R China
[2] State Key Lab Explos Sci & Technol, Beijing, Peoples R China
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2011年 / 528卷 / 06期
关键词：
Adiabatic shear band; Dynamic recrystallization; Phase transformation; Titanium alloys; STRAIN-RATE DEFORMATION; STAINLESS-STEEL; DYNAMIC RECRYSTALLIZATION; PHASE-TRANSFORMATION; PLASTIC-DEFORMATION; RATE BEHAVIOR; TITANIUM; LOCALIZATION; TANTALUM; COPPER;
D O I：
10.1016/j.msea.2010.12.053
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The adiabatic shear band (ASB) was obtained by split Hopkinson pressure bar (SHPB) technique in the hat-shaped specimen of a near beta-Ti alloy. The microstructure and the phase transformation within the ASB were investigated by means of TEM. The results show that the elongated subgrains with the width of 0.2-0.4 mu m have been observed in the shear band boundary, while the microstructure inside the ASB consists of fine equiaxed subgrains that are three orders of magnitude smaller than the grains in the matrix. The beta -> omega((althermal)) phase transformation has been observed in the ASB, and further analysis indicates that the shear band offers thermodynamic and kinetic conditions for the omega((althermal)) phase formation and the high alloying of this alloy is another essential factor for this transformation to take place. The thermo-mechanical history during the shear localization is calculated. The rotational dynamic recrystallization (RDR) mechanism is used to explain the microstructure evolution mechanism in the shear band. Kinetic calculations indicate that the recrystallized fine subgrains are formed during the deformation and do not undergo significant growth by grain boundary migration after deformation. (C) 2010 Elsevier B.V. All rights reserved.
引用
收藏
页码：2787 / 2794
页数：8
相关论文
共 50 条
  • [41] Quantitative microstructural characterization of a near beta Ti alloy, Ti-5553 under different processing conditions
    Kar, Sujoy Kumar
    Ghosh, Atasi
    Fulzele, Nishant
    Bhattacharjee, Amit
    MATERIALS CHARACTERIZATION, 2013, 81 : 37 - 48
  • [42] A method for calculating damage evolution in adiabatic shear band of titanium alloy
    王学滨
    TransactionsofNonferrousMetalsSocietyofChina, 2009, 19 (05) : 1280 - 1285
  • [43] Microstructure evolution of adiabatic shear bands in AM60B magnesium alloy under ballistic impact
    Zhen, L.
    Zou, D. L.
    Xu, C. Y.
    Shao, W. Z.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2010, 527 (21-22): : 5728 - 5733
  • [44] Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution
    Qin, Dong-yang
    Miao, Ying-gang
    Li, Yu-long
    DEFENCE TECHNOLOGY, 2022, 18 (11) : 2045 - 2051
  • [45] Effect of microstructure on adiabatic shear band bifurcation in Ti-6Al-4V alloys under ballistic impact
    Sun, Kai
    Yu, Xiaodong
    Tan, Chengwen
    Ma, Honglei
    Wang, Fuchi
    Cai, Hongnian
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 595 : 247 - 256
  • [46] Analysis and characterization by electron backscatter diffraction of microstructural evolution in the adiabatic shear bands in Fe-Cr-Ni alloys
    Yang, Huajie
    Xu, Yongbo
    Seki, Yasuaki
    Nesterenko, Vitali F.
    Meyers, Marc Andre
    JOURNAL OF MATERIALS RESEARCH, 2009, 24 (08) : 2617 - 2627
  • [47] The microstructure characterization of adiabatic shearing band in Ti-17 alloy at high strain rates and elevated temperatures
    Wang, Yubo
    Zeng, Weidong
    Sun, Xin
    Xu, Jianwei
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 677 : 325 - 331
  • [48] Formation and evolution of adiabatic shear bands in zirconium alloy impacted by split Hopkinson pressure bar
    Zou, D. L.
    Luan, B. F.
    Liu, Q.
    Chai, L. J.
    Chen, J. W.
    JOURNAL OF NUCLEAR MATERIALS, 2013, 437 (1-3) : 380 - 388
  • [49] Adiabatic Shear Band of TC4 Alloy during Warm Compression
    Ge Changjian
    Li Miaoquan
    RARE METAL MATERIALS AND ENGINEERING, 2014, 43 (09) : 2069 - 2074
  • [50] Microstructural evolution in NiTi alloy subjected to surface mechanical attrition treatment and mechanism
    Hu, T.
    Chu, C. L.
    Wu, S. L.
    Xu, R. Z.
    Sun, G. Y.
    Hung, T. F.
    Yeung, K. W. K.
    Wu, Z. W.
    Li, G. Y.
    Chu, Paul K.
    INTERMETALLICS, 2011, 19 (08) : 1136 - 1145
12345