Influence of the temperature on residual stresses and springback effect in an aluminium alloy

被引:66
作者
Greze, R. [1 ]
Manach, P. Y. [1 ]
Laurent, H. [1 ,2 ]
Thuillier, S. [1 ]
Menezes, L. F. [2 ]
机构
[1] Univ Bretagne Sud, Univ Europeenne Bretagne, LIMATB, F-56321 Lorient, France
[2] Univ Coimbra, Dept Engn Mecan, CEMUC, P-3030201 Coimbra, Portugal
关键词
Springback; Deep drawing; Temperature; AA5754-0 aluminium alloy; Split-ring test; WARM; MAGNESIUM;
D O I
10.1016/j.ijmecsci.2010.04.008
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
This study deals with the experimental and numerical investigation of springback in an aluminium alloy at different temperatures. An experimental split-ring test is performed on a AA5754-O alloy using a laboratory drawing device. The influence of temperature during forming over springback is measured from room temperature to 200 degrees C. The temperature is the same for all tools and is maintained constant during all the forming process. The experimental results are compared to numerical simulations performed with the finite element code Abaqus. Material parameters are identified using uniaxial tensile tests at different temperatures and several strain rates in order to take into account both temperature and viscous effects in a coupled thermomechanical constitutive law. The stress and strain states in the cup at the end of the drawing and after springback are analyzed as a function of temperature and a detailed study of stress distributions in the thickness of the blank is proposed. It is shown that the effect of temperature tends to decrease the stress gradient in the cup wall that is directly linked to the decrease of the springback opening of the ring. The distribution of the hoop stress in the cup wall is the main factor influencing the springback mechanism in warm forming condition. (C) 2010 Elsevier Ltd. All rights reserved.
引用
收藏
页码:1094 / 1100
页数:7
相关论文
共 27 条
[1]   Forming of aluminum alloys at elevated temperatures - Part 1: Material characterization [J].
Abedrabbo, N ;
Pourboghrat, F ;
Carsley, J .
INTERNATIONAL JOURNAL OF PLASTICITY, 2006, 22 (02) :314-341
[2]   ALLOYING ALUMINUM WITH MAGNESIUM FOR DUCTILITY AT WARM TEMPERATURES (25 TO 250-DEGREES-C) [J].
AYRES, RA .
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1979, 10 (07) :849-854
[3]   Feasibility of warm drawing of aluminium products [J].
Bolt, PJ ;
Lamboo, NAPM ;
Rozier, PJCM .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2001, 115 (01) :118-121
[4]  
DEMERI MY, 2000, BENCHMARK TEST SPRIN
[5]  
FINCH DM, 1946, ASM T, V36, P254
[6]   Robustness of the sheet metal springback cup test [J].
Foecke, T. ;
Gnaeupel-Herold, T. .
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2006, 37A (12) :3503-3510
[7]  
Fukui S, 1948, REP I PHYS CHEM RES, V24, P209
[8]  
GREZE R, 2007, 10 ESAFORM C MAT FOR
[9]  
JESWIET J, 2000, CIRP J MANUF SCI TEC, V1, P2
[10]   Numerical investigations on springback characteristics of aluminum sheet metal alloys in warm forming conditions [J].
Kim, Hong Seok ;
Koc, Muammer .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 204 (1-3) :370-383