Hetero-deformation-induced stress in additively manufactured 316L stainless steel

被引：89
作者：
Kong, Decheng [1 ,2 ]
Dong, Chaofang [1 ]
Ni, Xiaoqing [3 ]
Liang, Zhang [3 ]
Man, Cheng [4 ]
Li, Xiaogang [1 ]
机构：
[1] Univ Sci & Technol Beijing, Beijing Adv Innovat Ctr Mat Genome Engn, Beijing 100083, Peoples R China
[2] MIT, Dept Mat Sci & Engn, Cambridge, MA 02139 USA
[3] Shanghai Res Inst Mat, Shanghai Engn Res Ctr 3D Printing Mat, Shanghai, Peoples R China
[4] Ocean Univ China, Sch Mat Sci & Engn, Qingdao, Peoples R China
来源：
MATERIALS RESEARCH LETTERS | 2020年 / 8卷 / 10期
基金：
中国国家自然科学基金;
关键词：
Selective laser melting; 316L stainless steel; HDI stress; cellular structure; MICROSTRUCTURE; DISLOCATIONS; MECHANISMS; STRENGTH; NETWORK;
D O I：
10.1080/21663831.2020.1775149
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Impact statement Heterogeneous cellular structure combined with bimodal grain structure contributed to the high hetero-deformation-induced stress in additively manufactured 316L SS, the former effect was lower compared to the latter. Heterogeneous cellular structure combined with bimodal grain structure contributed to the high hetero-deformation-induced (HDI) stress in selective laser melted 316L stainless steel (SLMed 316L SS) and high grain boundary density at molten pool boundaries and thick cellular boundaries inside grains both acted as hard domains. However, the HDI hardening rate caused by cellular boundary was lower compared with the traditional grain boundary due to its weaker dislocation motion resistance. Under high deformation, massive deformation-induced twins penetrated the cellular boundary and distorted its configuration; therefore, grain boundary heterogeneity dominated the overall HDI stress in SLMed 316L SS after large deformation.
引用
收藏
页码：390 / 397
页数：8
相关论文
共 24 条
  • [1] CHEN WT, 2019, NAT COMMUN, V10, P1, DOI DOI 10.1038/s41467-018-07882-8
  • [2] Structure-property optimization of ultrafine-grained dual-phase steels using a micro structure-based strain hardening model
    Delince, M.
    Brechet, Y.
    Embury, J. D.
    Geers, M. G. D.
    Jacques, P. J.
    Pardoen, T.
    [J]. ACTA MATERIALIA, 2007, 55 (07) : 2337 - 2350
  • [3] Fang XT, 2010, ACTA MAT, V186, P644
  • [4] Measurements of stress fields near a grain boundary: Exploring blocked arrays of dislocations in 3D
    Guo, Y.
    Collins, D. M.
    Tarleton, E.
    Hofmann, F.
    Tischler, J.
    Liu, W.
    Xu, R.
    Wilkinson, A. J.
    Britton, T. B.
    [J]. ACTA MATERIALIA, 2015, 96 : 229 - 236
  • [5] Bio-functional and anti-corrosive 3D printing 316L stainless steel fabricated by selective laser melting
    Kong, Decheng
    Ni, Xiaoqing
    Dong, Chaofang
    Lei, Xiaowei
    Zhang, Liang
    Man, Cheng
    Yao, Jizheng
    Cheng, Xuequn
    Li, Xiaogang
    [J]. MATERIALS & DESIGN, 2018, 152 : 88 - 101
  • [6] Heat treatment effect on the microstructure and corrosion behavior of 316L stainless steel fabricated by selective laser melting for proton exchange membrane fuel cells
    Kong, Decheng
    Ni, Xiaoqing
    Dong, Chaofang
    Zhang, Liang
    Man, Cheng
    Yao, Jizheng
    Xiao, Kui
    Li, Xiaogang
    [J]. ELECTROCHIMICA ACTA, 2018, 276 : 293 - 303
  • [7] Kou S., 2003, WELDING METALLURGY, V2
  • [8] Stress relaxation and the cellular structure-dependence of plastic deformation in additively manufactured AlSi10Mg alloys
    Li, Zan
    Li, Zhiqiang
    Tan, Zhanqiu
    Xiong, Ding-Bang
    Guo, Qiang
    [J]. INTERNATIONAL JOURNAL OF PLASTICITY, 2020, 127
  • [9] Strengthening and hardening mechanisms of additively manufactured stainless steels: The role of cell sizes
    Li, Zan
    He, Bo
    Guo, Qiang
    [J]. SCRIPTA MATERIALIA, 2020, 177 : 17 - 21
  • [10] Dislocation network in additive manufactured steel breaks strength-ductility trade-off
    Liu, Leifeng
    Ding, Qingqing
    Zhong, Yuan
    Zou, Ji
    Wu, Jing
    Chiu, Yu-Lung
    Li, Jixue
    Zhang, Ze
    Yu, Qian
    Shen, Zhijian
    [J]. MATERIALS TODAY, 2018, 21 (04) : 354 - 361
123