A study of hot compression behavior of an as-cast FeCrCuNi2Mn2 high-entropy alloy

被引:16
作者
Sajadi, Seyyed Ali [1 ]
Toroghinejad, Mohammad Reza [1 ,2 ]
Rezaeian, Ahmad [1 ]
Ebrahimi, Gholam Reza [3 ]
机构
[1] Isfahan Univ Technol, Dept Mat Engn, Esfahan 8415683111, Iran
[2] Shahid Beheshti Univ, Fac Mech & Energy Engn, Tehran, Iran
[3] Ferdowsi Univ Mashhad, Mat & Met Engn Dept, Mashhad, Razavi Khorasan, Iran
关键词
FeCrCuNi2Mn2 high-entropy alloy; hot compression; Constitutive modeling; dynamic recrystallization; work hardening rate; microstructure; DEFORMATION-BEHAVIOR; DYNAMIC RECRYSTALLIZATION; CONSTITUTIVE ANALYSIS; PROCESSING MAPS; FLOW;
D O I
10.1016/j.jallcom.2021.162732
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
In this study, hot deformation behavior of an as-cast FeCrCuNi2Mn2 high-entropy alloy (HEA) was evaluated. For this purpose, hot compression tests were carried out in the temperature range of 600-1000 degrees C and initial strain rate range of 0.001-0.1 s(-1). Flow stresses under different deformation conditions were then friction-corrected. Work hardening rate analysis was used to evaluate the occurrence of dynamic re crystallization. Microstructures of the hot compressed specimens were characterized using optical microscopy. Strain-dependent constitutive equations were developed using the data obtained from the Sellars-Tegart-Garofalo equation. The critical and peak strain and the critical and peak stress, as dynamic recrystallization parameters, were extracted from the work hardening rate versus stress curves. The results indicated that the modeled flow stresses were generally lower than the measured ones, which could be attributed to the impact of friction on the flow stress. Microstructural observations after hot compression tests as well as evaluation of work hardening rate versus stress curves showed typical dynamic re crystallization characteristics under different deformation conditions. In addition, with increase in deformation temperature and decrease in strain rate, more DRX grains were formed along grain boundaries and shear bands, resulting in a decrease in the flow stress. The size of the DRX grains was strongly affected by deformation temperature and increased with increase in temperature. The normalized critical stress and strain for the initiation of DRX were calculated as epsilon(c)/epsilon(p) = 0.60 and sigma c/sigma p = 0.86, respectively. The activation energy of hot deformation was determined to be 708 kJ/mol. It was noticed that the developed constitutive equations could accurately predict the flow stress behavior of the studied alloy over a wide range of experimental conditions. (C) 2021 Elsevier B.V. All rights reserved.
引用
收藏
页数:15
相关论文
共 50 条
  • [41] Room-Temperature Superformability in Novel As-Cast High-Entropy Alloy During Compressive Loading
    Dutta, A.
    Tung, Shu-Yi
    Gupta, Saurabh Kumar
    Tsai, Ming-Hung
    Nene, Saurabh S. S.
    ADVANCED ENGINEERING MATERIALS, 2023, 25 (08)
  • [42] Hot Compression Deformation Behavior and Microstructure of As-Cast and Homogenized AA2195 Al-Li Alloy
    Zhang, Jin
    Liu, Zemeng
    Shi, Dongfeng
    METALS, 2022, 12 (10)
  • [43] Effects of second phases on deformation behavior and dynamic recrystallization of as-cast Mg-4.3Li-4.1Zn-1.4Y alloy during hot compression
    Zhou, Yucheng
    Chen, Zhaoyun
    Ji, Jinghan
    Sun, Zhijie
    JOURNAL OF ALLOYS AND COMPOUNDS, 2019, 770 : 540 - 548
  • [44] STUDY OF HOT DEFORMATION BEHAVIOR OF CuFe2 ALLOY
    Schindler, I
    Sauer, M.
    Kawulok, P.
    Rodak, K.
    Hadasik, E.
    Jablonska, M. Barbara
    Rusz, S.
    Sevcak, V
    ARCHIVES OF METALLURGY AND MATERIALS, 2019, 64 (02) : 701 - 706
  • [45] Study of hot forging behavior of as-cast Mg-3Al-1Zn-2Ca alloy towards optimization of its hot workability
    Suresh, K.
    Rao, K. P.
    Prasad, Y. V. R. K.
    Hort, N.
    Kainer, K. U.
    MATERIALS & DESIGN, 2014, 57 : 697 - 704
  • [46] Unleashing the microstructural evolutions during hot deformation of as-cast AlCoCrFeNi2.1 eutectic high entropy alloy
    Charkhchian, J.
    Zarei-Hanzaki, A.
    Schwarz, T. M.
    Lawitzki, R.
    Schmitz, G.
    Schell, N.
    Shen, Jiajia
    Oliveira, J. P.
    Waryoba, Daudi
    Abedi, H. R.
    INTERMETALLICS, 2024, 168
  • [47] Revealing the Effects of Friction Stir Processing on the Microstructural Evolutions and Mechanical Properties of As-Cast Interstitial FeMnCoCrN High-Entropy Alloy
    Abbasi, Alireza
    Zarei-Hanzaki, Abbas
    Charkhchian, Javad
    Moshiri, Ali
    Malayeri, Niyusha Akhavan
    Lee, Jongwon
    Park, Nokeun
    Abedi, Hamid Reza
    ADVANCED ENGINEERING MATERIALS, 2024, 26 (07)
  • [48] Aging behavior of a CuCr2Fe2NiMn high-entropy alloy
    Ren, B.
    Liu, Z. X.
    Cai, B.
    Wang, M. X.
    Shi, L.
    MATERIALS & DESIGN, 2012, 33 : 121 - 126
  • [49] Characterization of hot deformation behavior of Al0.3CoCrFeNi high-entropy alloy and development of processing map
    Patnamsetty, Madan
    Ghosh, Sumit
    Somani, Mahesh C.
    Peura, Pasi
    JOURNAL OF ALLOYS AND COMPOUNDS, 2022, 914
  • [50] Microstructure and mechanical property of as-cast, -homogenized, and -deformed AlxCoCrFeNi (0 ≤ x ≤ 2) high-entropy alloys
    Kao, Yih-Farn
    Chen, Ting-Jie
    Chen, Swe-Kai
    Yeh, Jien-Wei
    JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 488 (01) : 57 - 64