A study of hot compression behavior of an as-cast FeCrCuNi2Mn2 high-entropy alloy

被引:16
|
作者
Sajadi, Seyyed Ali [1 ]
Toroghinejad, Mohammad Reza [1 ,2 ]
Rezaeian, Ahmad [1 ]
Ebrahimi, Gholam Reza [3 ]
机构
[1] Isfahan Univ Technol, Dept Mat Engn, Esfahan 8415683111, Iran
[2] Shahid Beheshti Univ, Fac Mech & Energy Engn, Tehran, Iran
[3] Ferdowsi Univ Mashhad, Mat & Met Engn Dept, Mashhad, Razavi Khorasan, Iran
关键词
FeCrCuNi2Mn2 high-entropy alloy; hot compression; Constitutive modeling; dynamic recrystallization; work hardening rate; microstructure; DEFORMATION-BEHAVIOR; DYNAMIC RECRYSTALLIZATION; CONSTITUTIVE ANALYSIS; PROCESSING MAPS; FLOW;
D O I
10.1016/j.jallcom.2021.162732
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
In this study, hot deformation behavior of an as-cast FeCrCuNi2Mn2 high-entropy alloy (HEA) was evaluated. For this purpose, hot compression tests were carried out in the temperature range of 600-1000 degrees C and initial strain rate range of 0.001-0.1 s(-1). Flow stresses under different deformation conditions were then friction-corrected. Work hardening rate analysis was used to evaluate the occurrence of dynamic re crystallization. Microstructures of the hot compressed specimens were characterized using optical microscopy. Strain-dependent constitutive equations were developed using the data obtained from the Sellars-Tegart-Garofalo equation. The critical and peak strain and the critical and peak stress, as dynamic recrystallization parameters, were extracted from the work hardening rate versus stress curves. The results indicated that the modeled flow stresses were generally lower than the measured ones, which could be attributed to the impact of friction on the flow stress. Microstructural observations after hot compression tests as well as evaluation of work hardening rate versus stress curves showed typical dynamic re crystallization characteristics under different deformation conditions. In addition, with increase in deformation temperature and decrease in strain rate, more DRX grains were formed along grain boundaries and shear bands, resulting in a decrease in the flow stress. The size of the DRX grains was strongly affected by deformation temperature and increased with increase in temperature. The normalized critical stress and strain for the initiation of DRX were calculated as epsilon(c)/epsilon(p) = 0.60 and sigma c/sigma p = 0.86, respectively. The activation energy of hot deformation was determined to be 708 kJ/mol. It was noticed that the developed constitutive equations could accurately predict the flow stress behavior of the studied alloy over a wide range of experimental conditions. (C) 2021 Elsevier B.V. All rights reserved.
引用
收藏
页数:15
相关论文
共 50 条
  • [21] Tensile Properties and Serrated Flow Behavior of As-Cast CoCrFeMnNi High-Entropy Alloy at Room and Elevated Temperatures
    Kim, Jeoung Han
    Na, Young Sang
    METALS AND MATERIALS INTERNATIONAL, 2019, 25 (02) : 296 - 303
  • [22] High-temperature tensile deformation behavior of hot rolled CrMnFeCoNi high-entropy alloy
    Jang, Min Ji
    Praveen, S.
    Sung, Hyun Je
    Bae, Jae Wung
    Moon, Jongun
    Kim, Hyoung Seop
    JOURNAL OF ALLOYS AND COMPOUNDS, 2018, 730 : 242 - 248
  • [23] Effect of Mn on microstructure and tensile properties of as-cast Al0.5CoFeNiC0.1 high-entropy alloy
    Zhou, Xueyang
    Chen, Jian
    Ding, Rengen
    Wu, Haoyue
    Lu, Shuaidan
    He, Jiahua
    Pan, Hongge
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2023, 873
  • [24] Hot deformation behavior analysis of as-cast CoCrFeNi high entropy alloy using Arrhenius-type and artificial neural network models
    Karimzadeh, M.
    Malekan, M.
    Mirzadeh, H.
    Saini, N.
    Li, L.
    INTERMETALLICS, 2024, 168
  • [25] On the brittle-to-ductile transition of the as-cast TiVNbTa refractory high-entropy alloy
    Scales, R. J.
    Armstrong, D. E. J.
    Wilkinson, A. J.
    Li, B-S.
    MATERIALIA, 2020, 14
  • [26] An as-cast high-entropy alloy with remarkable mechanical properties strengthened by nanometer precipitates
    Qin, Gang
    Chen, Ruirun
    Liaw, Peter K.
    Gao, Yanfei
    Wang, Liang
    Su, Yanqing
    Ding, Hongsheng
    Guo, Jingjie
    Li, Xiaoqing
    NANOSCALE, 2020, 12 (06) : 3965 - 3976
  • [27] Effect of Yttrium Addition (0.2%) on the Hot Compression Behavior of the As-cast Mg-Sn Alloy
    Yang Qiurong
    Zeng Ying
    Zhou Mingyang
    Huang Guanghao
    Ren Lingbao
    Lu Jiawei
    Yin Dongdi
    Jiang Bing
    RARE METAL MATERIALS AND ENGINEERING, 2019, 48 (07) : 2275 - 2283
  • [28] Flow Behavior and Microstructure of Hot-Worked TiNbTaVW Refractory High-Entropy Alloy
    Bamisaye, Olufemi Sylvester
    Maledi, Nthabiseng
    Van der Merwe, Josias
    Klenam, Desmond
    Bodunrin, Michael
    ADVANCED ENGINEERING MATERIALS, 2024, 26 (20)
  • [29] Deformation behavior and microstructure evolution of as-cast Ti2ZrMo0.5Nb0.5 high entropy alloy
    Xu, Lijuan
    Chen, Zhaoqi
    Zheng, Yunfei
    Wang, Xiaohan
    Han, Shiwei
    Xiao, Shulong
    Chen, Yuyong
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2021, 13 : 2469 - 2481
  • [30] Hot deformation behavior of Ni61Fe10Cr10Al17Mo2 high-entropy alloy with hierarchical structure
    Wang, Jinyu
    Zhao, Jiajun
    Jia, Yuhao
    Fan, Xiaoguang
    He, Feng
    Luo, Xian
    Li, Junjie
    Wang, Zhijun
    Wang, Jincheng
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 26 : 6041 - 6052