Effect of the Fraction of Steel 4605 Powder in the Load in Injection Molding with the Use of a Polymer-Based Binder

被引：12

作者：

Momeni, Vaxid ^{[1
]}

Alaei, Mohammed Hossein ^{[2
]}

Askari, Ali ^{[1
]}

Rahitni, Amir Hossein ^{[1
]}

Nekouee, Khanali ^{[2
]}

机构：

[1] Malek Ashtar Univ Technol, Mech Dept, Tehran, Iran

[2] Malek Ashtar Univ Technol, Ctr Composite Mat, Tehran, Iran

来源：

METAL SCIENCE AND HEAT TREATMENT | 2020年 / 61卷 / 11-12期

关键词：

metal injection molding; polymer-based binder; powder loading; steel powder; mechanical properties; rheological properties; FEEDSTOCK; SIMULATIONS;

D O I：

10.1007/s11041-020-00499-z

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

The effect of the relative fraction of powder of steel 4605 (0.42% C, 2.15% Ni, 0.49% Mo, 0.1% Si) mixed with a polymer binder in injection molding of billets (the MIM technology) on their tensile mechanical properties, hardness, density and toughness is studied. The polymer binder is based on high-pressure polyethylene (HDPE), paraffin wax (PW) and stearic acid (SA). It is shown that the mechanical properties, the density and the toughness increase with the proportion of the powder in the working mixture (feedstock), and the combination of the strength and formability is the best at 62 vol.% powder in the feedstock.

引用

页码：777 / 781

页数：5

共 13 条

[1] Effect of the Fraction of Steel 4605 Powder in the Load in Injection Molding with the Use of a Polymer-Based Binder
Vaxid Momeni
Mohammed Hossein Alaei
Ali Askari
Amir Hossein Rahimi
Khanali Nekouee
Metal Science and Heat Treatment, 2020, 61 : 777 - 781
[2] Investigating metal injection molding of 4605 low-alloy steel powder-polymer mixture: parametric optimization of the injection stage using RSM technique
Rezaei, Sina
Askari, Ali
IRANIAN POLYMER JOURNAL, 2025, 34 (04) : 453 - 464
[3] Study of hyperbranched polymer on POM-based binder in metal injection molding
Jiang, Xingquan
Li, Duxin
Lu, Renwei
Yang, Zhongchen
Liu, Zhiyong
MATERIALS RESEARCH EXPRESS, 2019, 6 (12)
[4] Impact of binder constituents on the moldability of titanium-based feedstocks used in low-pressure powder injection molding
Cote, Raphael
Azzouni, Mohamed
Demers, Vincent
POWDER TECHNOLOGY, 2021, 381 : 255 - 268
[5] Polymer based binder materials for various metal injection molding processes: Salient aspects and recent trends
Tadi, Siva Prasad
Koppisetti, Dileep
Palisetti, Venkata Krishna Teja
Palivela, Bhargav Chandan
Mamilla, Ravi Sankar
JOURNAL OF MANUFACTURING PROCESSES, 2025, 133 : 322 - 353
[6] Effect of Increased Powder-Binder Adhesion by Backbone Grafting on the Properties of Feedstocks for Ceramic Injection Molding
Ghasemi-Mobarakeh, Laleh
Cano, Santiago
Momeni, Vahid
Liu, Dongyan
Duretek, Ivica
Riess, Gisbert
Kukla, Christian
Holzer, Clemens
POLYMERS, 2022, 14 (17)
[7] Optimization of Injection Molding and Solvent Debinding Parameters of Stainless Steel Powder (SS316L) Based Feedstock for Metal Injection Molding
Chua, Muhammad Ilman Hakimi
Sulong, Abu Bakar
Abdullah, Mohd Fazuri
Muhamad, Norhamidi
SAINS MALAYSIANA, 2013, 42 (12): : 1743 - 1750
[8] The rheologyical effect of carbon nanotubes on the iron based metal powder injection molding feedstock
Liang Shuquan
Tang Yan
Zhang Yong
Zhong Jie
MULTI-FUNCTIONAL MATERIALS AND STRUCTURES II, PTS 1 AND 2, 2009, 79-82 : 469 - 472
[9] Powder injection molding of HA/Ti6Al4V composite using palm stearin as based binder for implant material
Arifin, Amir
Sulong, Abu Bakar
Muhamad, Norhamidi
Syarif, Junaidi
Ramli, Mohd Ikram
MATERIALS & DESIGN, 2015, 65 : 1028 - 1034
[10] Effect of curative in hydroxyl-terminated polybutadiene-based binder system on characteristic properties and kinetics of polymer-based energetic composite
Kishore, Prateek
Singh, Arjun
Kumar, Rajesh
Soni, Pramod Kumar
Thakur, Preeti
Thakur, Atul
JOURNAL OF ENERGETIC MATERIALS, 2024,

← 1 2 →