Determination of interfacial properties of thermal barrier coatings by shear test and inverse finite element method

被引：54

作者：

Xu, Zhi-Hui ^{[1
]}

Yang, Yingchao ^{[1
]}

Huang, Peng ^{[1
]}

Li, Xiaodong ^{[1
]}

机构：

[1] Univ S Carolina, Dept Mech Engn, Columbia, SC 29208 USA

来源：

ACTA MATERIALIA | 2010年 / 58卷 / 18期

关键词：

Interfacial properties; Thermal barrier coatings; Inverse finite element method; DELAMINATION TOUGHNESS; MECHANICAL-PROPERTIES; RESIDUAL-STRESSES; ELASTIC-MODULUS; BARB TEST; INDENTATION; SYSTEMS; FILMS; SPALLATION; SUBSTRATE;

D O I：

10.1016/j.actamat.2010.07.013

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Determination of interfacial properties of thermal barrier coatings (TBCs) is very important for designing and evaluating the durability of TBCs. A new method combining a simple shear test and an inverse finite element analysis was developed and applied to measure the interfacial properties of two flame-sprayed yttria-stabilized zirconia TBCs. Nanoindentation testing was performed to determine the mechanical properties of different materials of the TBC systems. Variation of the lateral force during the shear test was recorded and analyzed to obtain the nominal ultimate shear strength of TBCs. The interfacial properties, namely fracture energy and stress intensity factor (mode II), of different TBC systems under both as-deposited and heat-treated conditions were determined through inverse finite element analysis. (C) 2010 Acta Materialia Inc Published by Elsevier Ltd All rights reserved

引用

页码：5972 / 5979

页数：8

共 35 条

[1] Assessment of TBC systems failure mechanisms using a fracture mechanics approach [J].

Aktaa, J ;

Sfar, K ;

Munz, D .

ACTA MATERIALIA, 2005, 53 (16) :4399-4413

[2] Overview of identification methods of mechanical parameters based on full-field measurements [J].

Avril, Stephane ;

Bonnet, Marc ;

Bretelle, Anne-Sophie ;

Grediac, Michel ;

Hild, Francois ;

Ienny, Patrick ;

Latourte, Felix ;

Lemosse, Didier ;

Pagano, Stephane ;

Pagnacco, Emmanuel ;

Pierron, Fabrice .

EXPERIMENTAL MECHANICS, 2008, 48 (04) :381-402

[3] Analysis of a wedge impression test for measuring the interface toughness between films/coatings and ductile substrates [J].

Begley, MR ;

Mumm, DR ;

Evans, AG ;

Hutchinson, JW .

ACTA MATERIALIA, 2000, 48 (12) :3211-3220

[4] Inverse problems in elasticity [J].

Bonnet, M ;

Constantinescu, A .

INVERSE PROBLEMS, 2005, 21 (02) :R1-R50

[5] Finite element analysis of a barb test for thermal barrier coating delamination toughness measurement [J].

Cao, Ning-Yuan ;

Liu, Yu-Fu ;

Kagawa, Yutaka .

SURFACE & COATINGS TECHNOLOGY, 2008, 202 (13) :3109-3114

[6] The mechanics of the solder ball shear test and the effect of shear rate [J].

Chia, JYH ;

Cotterell, B ;

Chai, TC .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 417 (1-2) :259-274

[7] Materials design for the next generation thermal barrier coatings [J].

Clarke, DR ;

Levi, CG .

ANNUAL REVIEW OF MATERIALS RESEARCH, 2003, 33 :383-417

[8] On using a penalty-based cohesive-zone finite element approach, Part I: Elastic solution benchmarks [J].

Diehl, Ted .

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES, 2008, 28 (4-5) :237-255

[9] Measurement of the adhesion of a brittle film on a ductile substrate by indentation [J].

Drory, MD ;

Hutchinson, JW .

PROCEEDINGS OF THE ROYAL SOCIETY A-MATHEMATICAL PHYSICAL AND ENGINEERING SCIENCES, 1996, 452 (1953) :2319-2341

[10] Role of impact on determination of interfacial toughness measurement by indentation for thermal barrier coating systems [J].

Ekici, B .

SURFACE ENGINEERING, 2005, 21 (5-6) :456-462

← 1 2 3 4 →