General corrosion properties of modified PNC1520 austenitic stainless steel in supercritical water as a fuel cladding candidate material for supercritical water reactor

被引:15
作者
Nakazono, Y. [1 ]
Iwai, T. [1 ]
Abe, H. [1 ]
机构
[1] Univ Tokyo, Sch Engn, Nucl Profess Sch, Tokai, Ibaraki 3191188, Japan
来源
INTERNATIONAL CONFERENCE ON HIGH PRESSURE SCIENCE AND TECHNOLOGY, JOINT AIRAPT-22 AND HPCJ-50 | 2010年 / 215卷
关键词
D O I
10.1088/1742-6596/215/1/012094
中图分类号
TH7 [仪器、仪表];
学科分类号
0804 ; 080401 ; 081102 ;
摘要
The Super-Critical Water-cooled Reactor (SCWR) has been designed and investigated because of its high thermal efficiency and plant simplification. There are some advantages including the use of a single phase coolant with high enthalpy but there are numerous potential problems, particularly with materials. As the operating temperature of supercritical water reactor will be between 280 degrees C and 620 degrees C with a pressure of 25MPa, the selection of materials is difficult and important. Austenitic stainless steels were selected for possible use in supercritical water systems because of their corrosion resistance and radiation resistance. The PNC1520 austenitic stainless steel developed by Japan Atomic Energy Agency (JAEA) as a nuclear fuel cladding material for a Na-cooled fast breeder reactor. The corrosion data of PNC1520 in supercritical water (SCW) is required but does not exist. The purpose of the present study is to research the corrosion properties for PNC1520 austenitic stainless steel in supercritical water. The supercritical water corrosion test was performed for the standard PNC1520 (1520S) and the Ti-additional type of PNC1520 (1520Ti) by using a supercritical water autoclave. Corrosion tests on the austenitic 1520S and 1520Ti steels in supercritical water were performed at 400, 500 and 600 degrees C with exposures up to 1000h. The amount of weight gain, weight loss and weight of scale were evaluated after the corrosion test in supercritical water for both austenitic steels. After 1000h corrosion test performed, the weight gains of both austenitic stainless steels were less than 2 g/m(2) at 400 degrees C and 500 degrees C. But both weight gain and weight loss of 1520Ti were larger than those of 1520S at 600 degrees C. By increasing the temperature to 600 degrees C, the surface of 1520Ti was covered with magnetite formed in supercritical water and dissolution of the steel alloying elements has been observed. In view of corrosion, 1520S may have larger possibility than 1520Ti to adopt a supercritical water reactor core fuel cladding.
引用
收藏
页数:12
相关论文
共 10 条
[1]  
KANEDA J, 2007, P INT C ADV NUCL POW, P7500
[2]  
KASAHARA S, 2003, P INT C ADV NUCL POW, P1132
[3]  
KATSUMURA Y, 2003, P INT C ADV NUCL POW, P1178
[4]  
KOSHIZUKA S, 2000, P SCR 2000 C YOK JAP, P302
[5]  
MITTON DB, 2003, P INT C ADV NUCL POW, P1027
[6]  
OKA Y, 2000, P SCR 2000 NOV 6 8 T, P101
[7]  
SAITO N, 2006, P INT C ADV NUCL POW, P6137
[8]  
Tsuchiya Y, 2003, P INT C ADV NUCL POW, P1096
[9]   Corrosion and stress corrosion cracking in supercritical water [J].
Was, G. S. ;
Ampornrat, P. ;
Gupta, G. ;
Teysseyre, S. ;
West, E. A. ;
Allen, T. R. ;
Sridharan, K. ;
Tan, L. ;
Chen, Y. ;
Ren, X. ;
Pister, C. .
JOURNAL OF NUCLEAR MATERIALS, 2007, 371 (1-3) :176-201
[10]   Conceptual design of compact supercritical water-cooled fast reactor with thermal hydraulic coupling [J].
Yoo, Jaewoon ;
Ishiwatari, Yuki ;
Oka, Yoshiaki ;
Liu, Jie .
ANNALS OF NUCLEAR ENERGY, 2006, 33 (11-12) :945-956