Mechanical properties of Cr-O-N coatings deposited by cathodic arc evaporation

被引：36
|
作者：
Warcholinski, B. [1 ]
Gilewicz, A. [1 ]
Kuprin, A. S. [2 ]
Tolmachova, G. N. [2 ]
Ovcharenko, V. D. [2 ]
Kuznetsova, T. A. [3 ]
Zubar, T., I [3 ]
Khudoley, A. L. [3 ]
Chizhik, S. A. [3 ]
机构：
[1] Koszalin Univ Technol, Fac Technol & Educ, Koszalin, Poland
[2] Natl Sci Ctr Kharkov Inst Phys & Technol, Kharkov, Ukraine
[3] Natl Acad Sci Belarus, AV Luikov Heat & Mass Transfer Inst, Minsk, BELARUS
来源：
VACUUM | 2018年 / 156卷
关键词：
Cr-O-N; Arc deposition; AFM; Hardness; Adhesion; Wear; CRYSTAL-CHEMICAL APPROACH; SUBSTRATE BIAS VOLTAGE; OXYNITRIDE THIN-FILMS; OXYGEN-CONTENT; HARD COATINGS; TRIBOLOGICAL BEHAVIORS; OXIDATION RESISTANCE; DROPLET FORMATION; MICROSTRUCTURE; STEEL;
D O I：
10.1016/j.vacuum.2018.07.017
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Ternary chromium based coatings (Cr-O-N) were formed on HS6-5-2 steel substrates using a vacuum arc plasma flux coating system at different relative oxygen concentrations, O-2(x) = O-2/(N-2 + O-2). The mechanical and tribological properties of the coatings were characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), hardness measurements, wear test and adhesion tests (scratch test and Daimler-Benz test). Special attention was paid to coating adhesion and failure modes in the adhesion tests. The coefficient of friction, wear rate and adhesion decreased as the relative oxygen concentration increased. Hardness of the coatings showed the opposite effect, increasing from approximately 19 GPa-30 GPa. The dominant failure mode of Cr-O-N coatings was abrasion. Individual micro fragmentation was also observed for Cr-O-N coating with O-2(x) = 20%.
引用
收藏
页码：97 / 107
页数：11
相关论文
共 50 条
  • [41] Effect of Ni Content on the Microstructure, Performance, and Mechanical Properties of High-Entropy Alloy Nitride (AlCrTiMoVNi)N Coatings Produced by Cathodic Arc Evaporation
    Lothrop, Alex
    Huang, Xiao
    Yang, Qi
    METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS, 2023, 12 (06) : 1020 - 1036
  • [42] Correlation between target surface and layer nucleation in the synthesis of Al-Cr-O coatings deposited by reactive cathodic arc evaporation
    Ramm, Juergen
    Neels, Antonia
    Widrig, Beno
    Doebeli, Max
    Vieira, Leandro de Abreu
    Dommann, Alex
    Rudigier, Helmut
    SURFACE & COATINGS TECHNOLOGY, 2010, 205 (05): : 1356 - 1361
  • [43] RESULTS ON THE THERMAL-STABILITY OF CATHODIC ARC-DEPOSITED (CR,B)N COATINGS
    ROTHER, B
    KAPPL, H
    SURFACE & COATINGS TECHNOLOGY, 1995, 73 (1-2): : 14 - 17
  • [44] Cathodic arc deposited (Cr,Six)N coatings: From solid solution to nanocomposite structure
    Schmitt, T.
    Steyer, P.
    Fontaine, J.
    Mary, N.
    Esnouf, C.
    O'Sullivan, M.
    Sanchette, F.
    SURFACE & COATINGS TECHNOLOGY, 2012, 213 : 117 - 125
  • [45] Influence of deposition pressure on the structural mechanical and decorative properties of TiN thin films deposited by cathodic arc evaporation
    Lousa, A.
    Esteve, J.
    Mejia, J. P.
    Devia, A.
    VACUUM, 2007, 81 (11-12) : 1507 - 1510
  • [46] AlTiCrNO coatings for dry cutting deposited by reactive cathodic vacuum arc evaporation
    Vetter, J
    Krug, T
    von der Heide, V
    SURFACE & COATINGS TECHNOLOGY, 2003, 174 : 615 - 619
  • [47] Photocatalytic and antimicrobial properties of surgical implant coatings of titanium dioxide deposited though cathodic arc evaporation
    Lilja, Mirjam
    Forsgren, Johan
    Welch, Ken
    Astrand, Maria
    Engqvist, Hakan
    Stromme, Maria
    BIOTECHNOLOGY LETTERS, 2012, 34 (12) : 2299 - 2305
  • [48] Comparison of Mechanical and Tribological Properties of Nitride and Oxynitride Coatings Based on Chrome and Zirconium Obtained by Cathodic Arc Evaporation
    B. Warcholinski
    A. Gilewicz
    A. S. Kuprin
    G. N. Tolmachova
    V. D. Ovcharenko
    T. A. Kuznetsova
    V. A. Lapitskaya
    S. A. Chizhik
    Journal of Friction and Wear, 2019, 40 : 163 - 170
  • [49] Effect of microblasting on cathodic arc evaporation CrN coatings
    Montesano, L.
    Pola, A.
    Gelfi, M.
    Brisotto, M.
    Depero, L. E.
    La Vecchia, G. M.
    SURFACE ENGINEERING, 2013, 29 (09) : 683 - 688
  • [50] Microstructure and Mechanical Properties of TI(Cr)SiC(O)N Coatings Deposited by Plasma Enhanced Magnetron Sputtering
    Xin Xin
    Zhang Tengfei
    Wang Yu
    Yu Yan
    Leng Yongxiang
    Xie Dong
    Huang Nan
    RARE METAL MATERIALS AND ENGINEERING, 2017, 46 (07) : 1762 - 1767
12345