A numerical investigation of the thermal-hydraulic characteristics of perforated plate fin heat sinks

被引：45

作者：

Al-Sallami, Waleed ^{[1
]}

Al-Damook, Amer ^{[1
,2
]}

Thompson, H. M. ^{[1
]}

机构：

[1] Univ Leeds, Sch Mech Engn, Leeds, W Yorkshire, England

[2] Univ Anbar, Fac Engn, Mech Engn Dept, Ramadi, Iraq

来源：

INTERNATIONAL JOURNAL OF THERMAL SCIENCES | 2017年 / 121卷

关键词：

Perforated plate fins; k-omega SST model; Conjugate heat transfer; Electronic cooling applications; PERFORMANCE ANALYSIS; DESIGN PARAMETERS; TRANSFER ENHANCEMENT; EXTENDED SURFACES; TAGUCHI METHOD; STRIP FIN; AIR-FLOWS; PIN FINS; EXCHANGER; OPTIMIZATION;

D O I：

10.1016/j.ijthermalsci.2017.07.022

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

The benefits of using notch, slot and multiple circular perforations in plate fin heat sinks (PFHSs), are investigated numerically, using a conjugate heat transfer model. Comparisons show that each type of perforation can provide significantly reduced pressure drops over PFHSs but that fins with slot perforations provide the most effective design in terms of heat transfer and pressure drop. The practical benefits of each type of perforated fin for micro-electronics cooling is also explored and their capabilities of achieving low processor temperatures for reduced mechanical power consumption are quantified. (C) 2017 Elsevier Masson SAS. All rights reserved.

引用

页码：266 / 277

页数：12

共 43 条

[11] Optimization of the design parameters of Parallel-Plain Fin heat sink module cooling phenomenon based on the Taguchi method [J].

Chiang, KT .

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2005, 32 (09) :1193-1201

[12] Enhanced single- and two-phase transport phenomena using flow separation in a microgap with copper woven mesh coatings [J].

Dai, Xianming ;

Yang, Fanghao ;

Fang, Ruixian ;

Yemame, Tsegaye ;

Khan, Jamil A. ;

Li, Chen .

APPLIED THERMAL ENGINEERING, 2013, 54 (01) :281-288

[13] Thermal Design of Multistream Plate Fin Heat Exchangers-A State-of-the-Art Review [J].

Das, Prasanta Kumar ;

Ghosh, Indranil .

HEAT TRANSFER ENGINEERING, 2012, 33 (4-5) :284-300

[14]

Dhanawade K. H., 2010, International Conference on Frontiers in Automobile and Mechanical Engineering (FAME 2010), P192, DOI 10.1109/FAME.2010.5714845

[15]

Dhumne A., 2013, INT J ENG SCI TECHNO, V6, P125

[16] Thermal and hydraulic performance analysis of rectangular fin arrays with perforation size and number [J].

Ehteshum, Mehedi ;

Ali, Mohammad ;

Islam, Md Quamrul ;

Tabassum, Muhsia .

6th BSME International Conference on Thermal Engineering, 2015, 105 :184-191

[17] Thermal issues in next-generation integrated circuits [J].

Gurrum, SP ;

Suman, SK ;

Joshi, YK ;

Fedorov, AG .

IEEE TRANSACTIONS ON DEVICE AND MATERIALS RELIABILITY, 2004, 4 (04) :709-714

[18] Fork-shaped highly conductive pathways for maximum cooling in a heat generating piece [J].

Hajmohammadi, M. R. ;

Abianeh, V. Alizadeh ;

Moezzinajafabadi, M. ;

Daneshi, M. .

APPLIED THERMAL ENGINEERING, 2013, 61 (02) :228-235

[19]

Hopton P, 2013, P IEEE SEMICOND THER, P60, DOI 10.1109/SEMI-THERM.2013.6526806

[20] Nanofluid as a coolant for electronic devices (cooling of electronic devices) [J].

Ijam, Ali ;

Saidur, R. .

APPLIED THERMAL ENGINEERING, 2012, 32 :76-82

← 1 2 3 4 5 →