Vanillin Acrylate-Based Resins for Optical 3D Printing

被引:25
|
作者
Navaruckiene, Aukse [1 ]
Skliutas, Edvinas [2 ]
Kasetaite, Sigita [1 ]
Rekstyte, Sima [2 ]
Raudoniene, Vita [3 ]
Bridziuviene, Danguole [3 ]
Malinauskas, Mangirdas [2 ]
Ostrauskaite, Jolita [1 ]
机构
[1] Kaunas Univ Technol, Dept Polymer Chem & Technol, Radvilenu Rd 19, LT-50254 Kaunas, Lithuania
[2] Vilnius Univ, Fac Phys, Laser Res Ctr, Sauletekis Ave 10, LT-10223 Vilnius, Lithuania
[3] Nat Res Ctr, Biodeteriorat Res Lab, Akad Str 2, LT-08412 Vilnius, Lithuania
基金
欧盟地平线“2020”;
关键词
vanillin dimethacrylate; vanillin diacrylate; photopolymerization; optical 3D printing; direct laser writing; replica molding; PHOTOINITIATED POLYMERIZATION; PHOTOPOLYMERIZATION;
D O I
10.3390/polym12020397
中图分类号
O63 [高分子化学(高聚物)];
学科分类号
070305 ; 080501 ; 081704 ;
摘要
The investigation of biobased systems as photocurable resins for optical 3D printing has attracted great attention in recent years; therefore, novel vanillin acrylate-based resins were designed and investigated. Cross-linked polymers were prepared by radical photopolymerization of vanillin derivatives (vanillin dimethacrylate and vanillin diacrylate) using ethyl(2,4,6-trimethylbenzoyl)phenylphosphinate as photoinitiator. The changes of rheological properties were examined during the curing with ultraviolet/visible irradiation to detect the influences of solvent, photoinitiator, and vanillin derivative on cross-linking rate and network formation. Vanillin diacrylate-based polymers had higher values of yield of insoluble fraction, thermal stability, and better mechanical properties in comparison to vanillin dimethacrylate-based polymers. Moreover, the vanillin diacrylate polymer film showed a significant antimicrobial effect, only a bit weaker than that of chitosan film. Thermal and mechanical properties of vanillin acrylate-based polymers were comparable with those of commercial petroleum-derived materials used in optical 3D printing. Also, vanillin diacrylate proved to be well-suited for optical printing as was demonstrated by employing direct laser writing 3D lithography and microtransfer molding techniques.
引用
收藏
页数:14
相关论文
共 50 条
  • [31] Photoinitiator-Free Plasma-Induced Polymerization and Microstructuring of Acrylate-Based Coatings on 3D Substratesa
    Elsner, Christian
    Boulares-Pender, Alya
    Haenel, Martin
    Konieczny, Robert
    Kuehnel, Christa
    Buchmeiser, Michael R.
    MACROMOLECULAR MATERIALS AND ENGINEERING, 2009, 294 (6-7) : 422 - 431
  • [32] Optical Fiber-Assisted Printing: A Platform Technology for Straightforward Photopolymer Resins Patterning and Freeform 3D Printing
    Cianciosi, Alessandro
    Pfeiffle, Maximilian
    Wohlfahrt, Philipp
    Nuernberger, Severin
    Jungst, Tomasz
    ADVANCED SCIENCE, 2024, 11 (32)
  • [33] Castor oil-based UV-curable polyurethane acrylate resins for digital light processing (DLP) 3D printing technology
    Bhanushali, Haresh
    Mestry, Siddhesh
    Mhaske, S. T.
    JOURNAL OF APPLIED POLYMER SCIENCE, 2023, 140 (18)
  • [34] Rubber Seed Oil-Based UV-Curable Polyurethane Acrylate Resins for Digital Light Processing (DLP) 3D Printing
    Hu, Yun
    Zhu, Guoqiang
    Zhang, Jinshuai
    Huang, Jia
    Yu, Xixi
    Shang, Qianqian
    An, Rongrong
    Liu, Chengguo
    Hu, Lihong
    Zhou, Yonghong
    MOLECULES, 2021, 26 (18):
  • [35] Optimization and Testing of Hybrid 3D Printing Vitrimer Resins
    Casado, Jaime
    Konuray, Osman
    Benet, Gerard
    Fernandez-Francos, Xavier
    Morancho, Jose Maria
    Ramis, Xavier
    POLYMERS, 2022, 14 (23)
  • [36] Addressing mmWave Challenges with Dielectric Resins and 3D Printing
    Lambert, Philip
    MICROWAVE JOURNAL, 2022, 65 (04) : 62 - 72
  • [37] Development of Biocompatible Resins for 3D Printing of Direct Aligners
    Nakano, Haruhisa
    Kato, Riyu
    Kakami, Chifumi
    Okamoto, Hiroaki
    Mamada, Katsuyoshi
    Maki, Koutaro
    JOURNAL OF PHOTOPOLYMER SCIENCE AND TECHNOLOGY, 2019, 32 (02) : 209 - 216
  • [38] Synthesis of Bio-Based Polyester Resins for Vat Photopolymerization 3D Printing
    Cazin, Ines
    Ocepek, Martin
    Kecelj, Janez
    Strazar, Ales Stanislav
    Schloegl, Sandra
    MATERIALS, 2024, 17 (08)
  • [39] Graphene Oxide Based Transparent Resins For Accurate 3D Printing of Conductive Materials
    Tilve-Martinez, David
    Neri, Wilfrid
    Horaud, Dylan
    Vukadinovic, Nicolas
    Berton, Benoit
    Desmedt, Arnaud
    Yuan, Jinkai
    Poulin, Philippe
    ADVANCED FUNCTIONAL MATERIALS, 2023, 33 (21)
  • [40] Terpene- and terpenoid-based polymeric resins for stereolithography 3D printing
    Weems, Andrew C.
    Delle Chiaie, Kayla R.
    Worch, Joshua C.
    Stubbs, Connor J.
    Dove, Andrew P.
    POLYMER CHEMISTRY, 2019, 10 (44) : 5959 - 5966