Vanillin Acrylate-Based Resins for Optical 3D Printing

被引:25
|
作者
Navaruckiene, Aukse [1 ]
Skliutas, Edvinas [2 ]
Kasetaite, Sigita [1 ]
Rekstyte, Sima [2 ]
Raudoniene, Vita [3 ]
Bridziuviene, Danguole [3 ]
Malinauskas, Mangirdas [2 ]
Ostrauskaite, Jolita [1 ]
机构
[1] Kaunas Univ Technol, Dept Polymer Chem & Technol, Radvilenu Rd 19, LT-50254 Kaunas, Lithuania
[2] Vilnius Univ, Fac Phys, Laser Res Ctr, Sauletekis Ave 10, LT-10223 Vilnius, Lithuania
[3] Nat Res Ctr, Biodeteriorat Res Lab, Akad Str 2, LT-08412 Vilnius, Lithuania
基金
欧盟地平线“2020”;
关键词
vanillin dimethacrylate; vanillin diacrylate; photopolymerization; optical 3D printing; direct laser writing; replica molding; PHOTOINITIATED POLYMERIZATION; PHOTOPOLYMERIZATION;
D O I
10.3390/polym12020397
中图分类号
O63 [高分子化学(高聚物)];
学科分类号
070305 ; 080501 ; 081704 ;
摘要
The investigation of biobased systems as photocurable resins for optical 3D printing has attracted great attention in recent years; therefore, novel vanillin acrylate-based resins were designed and investigated. Cross-linked polymers were prepared by radical photopolymerization of vanillin derivatives (vanillin dimethacrylate and vanillin diacrylate) using ethyl(2,4,6-trimethylbenzoyl)phenylphosphinate as photoinitiator. The changes of rheological properties were examined during the curing with ultraviolet/visible irradiation to detect the influences of solvent, photoinitiator, and vanillin derivative on cross-linking rate and network formation. Vanillin diacrylate-based polymers had higher values of yield of insoluble fraction, thermal stability, and better mechanical properties in comparison to vanillin dimethacrylate-based polymers. Moreover, the vanillin diacrylate polymer film showed a significant antimicrobial effect, only a bit weaker than that of chitosan film. Thermal and mechanical properties of vanillin acrylate-based polymers were comparable with those of commercial petroleum-derived materials used in optical 3D printing. Also, vanillin diacrylate proved to be well-suited for optical printing as was demonstrated by employing direct laser writing 3D lithography and microtransfer molding techniques.
引用
收藏
页数:14
相关论文
共 50 条
  • [21] Effects of brushing on denture resins for 3D printing
    da Silva, Marcela Dantas Dias
    Nunes, Thais Soares Bezerra Santos
    Viotto, Hamile Emanuella do Carmo
    Souza, Raphael Freitas de
    Pero, Ana Carolina
    JOURNAL OF PROSTHODONTIC RESEARCH, 2024, 68 (02) : 191 - 192
  • [22] Bacterial cellulose growth on 3D acrylate-based microstructures fabricated by two-photon polymerization
    Otuka, Adriano J. G.
    Domeneguetti, Rafael R.
    Moraes, Jonathas Q. R.
    Balogh, Debora T.
    Ribeiro, Sidney J. L.
    Mendonca, Cleber R.
    JOURNAL OF PHYSICS-PHOTONICS, 2021, 3 (02):
  • [23] Tannin-Based Resins for 3D printing of Porous Carbon Architectures
    Blyweert, Pauline
    Nicolas, Vincent
    Macutkevic, Jan
    Fierro, Vanessa
    Celzard, Alain
    ACS Sustainable Chemistry and Engineering, 2022, 10 (23): : 7702 - 7711
  • [24] Tannin-Based Resins for 3D printing of Porous Carbon Architectures
    Blyweert, Pauline
    Nicolas, Vincent
    Macutkevic, Jan
    Fierro, Vanessa
    Celzard, Alain
    ACS SUSTAINABLE CHEMISTRY & ENGINEERING, 2022, 10 (23): : 7702 - 7711
  • [25] Experimental Design Optimization of Acrylate-Tannin Photocurable Resins for 3D Printing of Bio-Based Porous Carbon Architectures
    Blyweert, Pauline
    Nicolas, Vincent
    Fierro, Vanessa
    Celzard, Alain
    MOLECULES, 2022, 27 (07):
  • [26] Acrylate-based photosensitive resin for stereolithographic three-dimensional printing
    Zhang, Xueqian
    Xu, Yu
    Li, Lei
    Yan, Bei
    Bao, Jianjun
    Zhang, Aiming
    JOURNAL OF APPLIED POLYMER SCIENCE, 2019, 136 (21)
  • [27] (Meth)acrylate Contact Dermatitis due to 3D Printing
    Gisy, Jenny
    ALLERGO JOURNAL, 2024, 33 (04) : 8 - 9
  • [28] Ageing of acrylate-based resins for stereolithography: thermal and humidity ageing behaviour studies
    Troeger, Carola
    Bens, Arthur T.
    Bermes, Guenter
    Klemmer, Ricarda
    Lenz, Johannes
    Irsen, Stephan
    RAPID PROTOTYPING JOURNAL, 2008, 14 (05) : 305 - 317
  • [29] Nanowire enhanced dimensional accuracy in acrylate resin-based 3D printing
    Han, Yanyang
    Yeo, Chee Chuan J.
    Chen, Dairong
    Wang, Fei
    Chong, Yiting
    Li, Xu
    Jiao, Xiuling
    Wang, Fuke
    NEW JOURNAL OF CHEMISTRY, 2017, 41 (16) : 8407 - 8412
  • [30] 3D printing polyurethane acrylate(PUA) based elastomer and its mechanical behavior
    Li, Huan
    Liang, Lei
    Zeng, Wenxiang
    Deng, Yuancheng
    Ge, Nengpeng
    Shan, Wubin
    MATERIALS RESEARCH EXPRESS, 2023, 10 (05)