Effect of Zirconium Oxide Reinforcement on Microstructural, Electrochemical, and Mechanical Properties of TiNi Alloy Produced via Powder Metallurgy Route

被引:1
|
作者
Raza, S. Abbas [1 ]
Khan, M. Imran [1 ]
Karim, M. Ramzan Abdul [1 ]
Ali, Rashid [1 ]
Naseer, M. Umair [2 ]
Abbas, S. Zameer [1 ]
Ahmad, Mairaj [1 ]
机构
[1] Ghulam Ishaq Khan Inst Engn Sci & Technol, Fac Mat & Chem Engn, Dept Mat Sci & Engn, Swabi 23640, Kpk, Pakistan
[2] Skolkovo Inst Sci & Technol, Ulitsa Nobelya 3, Moscow 121205, Moscow Oblast, Russia
来源
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME | 2021年 / 143卷 / 04期
关键词
nitinol; zirconia; metal matrix composites; powder metallurgy; nano-indention; corrosion behavior; materials processing; mechanical behavior; metals; ceramics; intermetallics; microstructure property relationships; SHAPE-MEMORY ALLOY; CORROSION BEHAVIOR; MATRIX-COMPOSITES; TENSILE PROPERTIES; NITI; TRANSFORMATION; FABRICATION; RESISTANCE; PARTICLES; COATINGS;
D O I
10.1115/1.4051308
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
Equiatomic TiNi alloy composites, reinforced with 0, 5, 10, and 15 vol% ZrO2, were synthesized using conventional sintering approach. Equiatomic TiNi pre-alloyed powder and ZrO2 powder were mixed in planetary ball mill for 6 h followed by cold compaction and pressure-less sintering, respectively. The sintered density was found to vary inversely with the addition of ZrO2 content. The X-ray diffraction (XRD) spectra have shown the formation of multiple-phases which were resulted from the decomposition of the B19 ' and B2 phases of the equiatomic TiNi alloy due to the addition of ZrO2 and higher diffusion rate of Ni than that of Ti in the alloy composite. An increase in hardness was noted due to the addition of ZrO2, measured by micro and nanoindentation techniques. Potentiodynamic polarization scan revealed a 10% decrease in the corrosion rate of the composite containing 10 vol% ZrO2. Electrochemical impedance spectroscopy (EIS) results indicated an increase in passive layer resistance (R-coat) due to the increase in charge transfer resistance (R-ct) caused by the reduced leaching of ions from the surface.
引用
收藏
页数:12
相关论文
共 50 条
  • [1] Effect of sintering procedure on microstructure and mechanical properties of biomedical TiNbSn alloy produced via powder metallurgy
    Cakmak, Omer
    Kaya, Mehmet
    APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING, 2021, 127 (07):
  • [2] EFFECT OF NICKEL ON MECHANICAL PROPERTIES OF ALLOY STEEL PRODUCED BY POWDER METALLURGY
    Behera, D. K.
    Tripathi, Priyadarshini
    Chaubey, A. K.
    MATERIALS TODAY-PROCEEDINGS, 2018, 5 (01) : 1704 - 1710
  • [3] Effect of sintering procedure on microstructure and mechanical properties of biomedical TiNbSn alloy produced via powder metallurgy
    Ömer Çakmak
    Mehmet Kaya
    Applied Physics A, 2021, 127
  • [4] Microstructure and mechanical properties of a Mg-Zn-Y alloy produced by a powder metallurgy route
    Asgharzadeh, H.
    Yoon, E. Y.
    Chae, H. J.
    Kim, T. S.
    Lee, J. W.
    Kim, H. S.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2014, 586 : S95 - S100
  • [5] The effect of borax addition to aluminum alloy produced by powder metallurgy on mechanical and thermophysical properties
    Mutlu, Rasiha Nefise
    Acar, Aye Nur
    Gizir, Ahmet Murat
    ANTI-CORROSION METHODS AND MATERIALS, 2022, 69 (01) : 63 - 70
  • [6] The influence of microstructural characteristics on the mechanical properties of Ti6Al4V alloy produced by the powder metallurgy technique
    Bozic, Dusan
    Cvijovic, Ivana
    Vilotijevic, Miroljub
    Jovanovic, Milan T.
    JOURNAL OF THE SERBIAN CHEMICAL SOCIETY, 2006, 71 (8-9) : 985 - 992
  • [7] Effect of Shape Memory Heat Treatment on Microstructures and Mechanical Properties of Powder Metallurgy TiNi Shape Memory Alloy
    Soba, Ryoichi
    Tanabe, Yukiko
    Yonezawa, Takayuki
    Umeda, Junko
    Kondoh, Katsuyoshi
    MATERIALS TRANSACTIONS, 2018, 59 (05) : 805 - 810
  • [8] High temperature mechanical properties of low alloy steel foams produced by powder metallurgy
    Bekoz, Nuray
    Oktay, Enver
    MATERIALS & DESIGN, 2014, 53 : 482 - 489
  • [9] Effect of Silicon Carbide on Microstructural, Mechanical and Corrosion Behavior of Electrolytic Copper Matrix Composite Produced by the Powder Metallurgy Route
    M. Melwin Jagadeesh Sridhar
    M. Ravichandran
    M. Meignanamoorthy
    V. Mohanavel
    Silicon, 2022, 14 : 5877 - 5886
  • [10] Effect of ECAP on microstructure and mechanical properties of a commercial 6061 Al alloy produced by powder metallurgy
    Chang, SY
    Lee, KS
    Choi, SH
    Shin, DH
    JOURNAL OF ALLOYS AND COMPOUNDS, 2003, 354 (1-2) : 216 - 220