Deformation analysis of short glass fiber-reinforced polypropylene injection-molded plastic parts

被引：10

作者：

Siklo, B. ^{[1
]}

Cameron, K. ^{[2
]}

Kovacs, J. G. ^{[1
]}

机构：

[1] Budapest Univ Technol & Econ, Dept Polymer Engn, H-1111 Budapest, Hungary

[2] Univ W Scotland, Edinburgh, Midlothian, Scotland

来源：

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES | 2011年 / 30卷 / 16期

关键词：

warpage; corner effect; injection molding; deformation; injection mold; mold temperature; MECHANICAL-PROPERTIES; MOLDING PROCESS; WARPAGE; SHRINKAGE; PREDICTION; PARAMETERS; SIMULATION; STRESSES;

D O I：

10.1177/0731684411426203

中图分类号：

TB33 [复合材料];

学科分类号：

摘要：

The warpage of injection-molded plastic parts is a complex problem being affected by different technological parameters, material properties, and mold design. Hence, the description of the deformation is difficult as well. This article presents the effect of fiber content and mold temperature difference on the deformation of polypropylene parts. Based on the measurement results, a linear approximation and a calculation method are shown, which can be used to jointly determine the ideal fiber content and mold temperature difference to produce undeformed plastic parts.

引用

页码：1367 / 1372

页数：6

共 26 条

[1] Prediction of process-induced warpage in injection molded thermoplastics [J].

Akay, M ;

Ozden, S ;

Tansey, T .

POLYMER ENGINEERING AND SCIENCE, 1996, 36 (13) :1839-1846

[2]

Ammar A., 2003, International Journal of Forming Processes, V6, P53, DOI DOI 10.3166/IJFP.6.53-70

[3] Effect of mold temperature on short and long-term mechanical properties of PBT [J].

Banik, K. .

EXPRESS POLYMER LETTERS, 2008, 2 (02) :111-117

[4] A study of packing profile on injection molded part quality [J].

Chen, X ;

Gao, F .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2003, 358 (1-2) :205-213

[5] An experimental investigation of the effects of hot runner system on injection moulding process in comparison with conventional runner system [J].

Demirer, A. ;

Soydan, Y. ;

Kapti, A. O. .

MATERIALS & DESIGN, 2007, 28 (05) :1467-1476

[6] Modeling and investigation of the reinforcing effect of maize hull in PE matrix composites [J].

Dogossy, Gabor ;

Czigany, Tibor .

POLYMERS FOR ADVANCED TECHNOLOGIES, 2006, 17 (9-10) :825-829

[7] Modeling warpage in reinforced polymer disks [J].

Fahy, EJ .

POLYMER ENGINEERING AND SCIENCE, 1998, 38 (07) :1072-1084

[8]

Fischer J.M., 2003, HDB MOLDED PART SHRI

[9] Effect of temperature on tensile properties of injection moulded short glass fibre and glass bead filled ABS hybrids [J].

Hashemi, S. .

EXPRESS POLYMER LETTERS, 2008, 2 (07) :474-484

[10] Warpage of injection moulded plates and corner products [J].

Jansen, KMB ;

van Dijk, DJ ;

Keizer, KP .

INTERNATIONAL POLYMER PROCESSING, 1998, 13 (04) :417-424

← 1 2 3 →