SET UP OF AN EXPERIMENTAL FACILITY FOR THE INVESTIGATION OF WET COMPRESSION ON A MULTISTAGE COMPRESSOR

被引:0
作者
Bettocchi, R. [1 ]
Morini, M. [1 ]
Pinelli, M. [1 ]
Spina, P. R. [1 ]
Venturini, M. [1 ]
Torsello, G.
机构
[1] Univ Ferrara, Dipartimento Ingn, I-44122 Ferrara, Italy
来源
PROCEEDINGS OF THE ASME TURBO EXPO 2010, VOL 5 | 2010年
关键词
TURBINE FOGGING TECHNOLOGY; INLET;
D O I
暂无
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
At present, inlet fogging and wet compression are two of the most widely used approaches to enhance gas turbine performance, especially during hot seasons. However, potentially negative effects of these practices on long-term operational integrity of gas turbines should be evaluated carefully; in particular, wet compression may lead to the erosion of first compressor stages, due to the impact of water droplets within the flow at compressor intake. This issue is still controversial in technical literature, since only limited historical field operating data and information are available. Therefore, a test facility was specifically set up in the laboratories of the University of Ferrara, to evaluate the effects of wet compression on a small-size compressor. This paper presents the experimental facility developed for wet compression investigation and some preliminary results.
引用
收藏
页码:673 / 683
页数:11
相关论文
共 28 条
[1]  
Advisory Group for Aerospace Research & Development (AGARD), 1995, AGARDAR332
[2]  
[Anonymous], GT200959365 ASME
[3]  
BAGNOLI M, ASME J ENG GAS TURBI, V130
[4]   A multistage compressor test facility: Uncertainty analysis and preliminary test results [J].
Bettocchi, R ;
Pinelli, M ;
Spina, PR .
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2005, 127 (01) :170-177
[5]   Gas turbine fogging technology: A state-of-the-art review - Part III: Practical considerations and operational experience [J].
Bhargava, R. K. ;
Meher-Homji, C. B. ;
Chaker, M. A. ;
Bianchi, M. ;
Melino, F. ;
Peretto, A. ;
Ingistov, S. .
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2007, 129 (02) :461-472
[6]   Gas turbine fogging technology: A state-of-the-art review - Part I: Inlet evaporative fogging - Analytical and experimental aspects [J].
Bhargava, R. K. ;
Meher-Homji, C. B. ;
Chaker, M. A. ;
Bianchi, M. ;
Melino, F. ;
Peretto, A. ;
Ingistov, S. .
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2007, 129 (02) :443-453
[7]   Gas turbine fogging technology: A state-of-the-art review - Part II: Overspray fogging - Analytical and experimental aspects [J].
Bhargava, R. K. ;
Meher-Homji, C. B. ;
Chaker, M. A. ;
Bianchi, M. ;
Melino, F. ;
Peretto, A. ;
Ingistov, S. .
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2007, 129 (02) :454-460
[8]  
Bhargava R.K., 2009, ASME Paper, No.GT2009-59920
[9]  
Bhargava R. K., 2008, GT200850761 ASME
[10]  
BIANCHI M, ECOS 2007 20 INT C E