Processing and characterization of porous titanium for implants by using NaCl as space holder

被引：159

作者：

Torres, Y. ^{[1
]}

Pavon, J. J. ^{[2
]}

Rodriguez, J. A. ^{[1
]}

机构：

[1] Univ Seville, Dept Mech & Mat Engn, Seville 41092, Spain

[2] Univ Antioquia, Bioengn Programme, Biomat Res Grp BIOMAT, Medellin, Colombia

来源：

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 2012年 / 212卷 / 05期

关键词：

Porous titanium; Space-holder technique; Powder metallurgy; Dynamic Young's modulus; Stress shielding; MECHANICAL-PROPERTIES; NITI; TI;

D O I：

10.1016/j.jmatprotec.2011.12.015

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Porous samples of commercially pure titanium (CP Ti) were fabricated by using sodium chloride (NaCl) as space-holder with percentages between 40 and 70 vol%. The dissolution of NaCl in distilled water, the structural integrity of samples and the reproducibility of the procedure were studied as a step prior to sintering. All these parameters were evaluated in terms of the compaction pressure, temperature and agitation of water, and dissolution time. The characterization of samples included density, porosity and dynamic Young's modulus. The results indicate that the most efficient lixiviation, according to the desired balance of properties, was by immersion in hot water, without agitation and for prolonged cycles of immersion time. (C) 2011 Elsevier B.V. All rights reserved.

引用

页码：1061 / 1069

页数：9

共 20 条

[11] Pore diameter of more than 100 μm is not requisite for bone ingrowth in rabbits
Itälä, AI
Ylänen, HO
Ekholm, C
Karlsson, KH
Aro, HT
[J]. JOURNAL OF BIOMEDICAL MATERIALS RESEARCH, 2001, 58 (06): : 679 - 683
[12] Köhl M, 2008, POROUS METALS AND METALLIC FOAMS: METFOAM 2007, P295
[13] Acoustical and poromechanical characterisation of titanium scaffolds for biomedical applications
Muellner, H. W.
Fritsch, A.
Kohlhauser, C.
Reihsner, R.
Hellmich, C.
Godlinski, D.
Rota, A.
Slesinski, R.
Eberhardsteiner, J.
[J]. STRAIN, 2008, 44 (02) : 153 - 163
[14] Mechanical properties of porous titanium compacts prepared by powder sintering
Oh, IH
Nomura, N
Masahashi, N
Hanada, S
[J]. SCRIPTA MATERIALIA, 2003, 49 (12) : 1197 - 1202
[15] Mechanical evaluation of porous titanium (Ti6Al4V) structures with electron beam melting (EBM)
Parthasarathy, Jayanthi
Starly, Binil
Raman, Shivakumar
Christensen, Andy
[J]. JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS, 2010, 3 (03) : 249 - 259
[16] Patnaik P., 2003, HDB INORGANIC CHEM
[17] Shishkovsky IV, 2010, INT J SELF-PROPAG HI, V19, P157, DOI 10.3103/S1061386210020123
[18] Conventional Powder Metallurgy Process and Characterization of Porous Titanium for Biomedical Applications
Torres, Y.
Pavon, J. J.
Nieto, I.
Rodriguez, J. A.
[J]. METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE, 2011, 42 (04): : 891 - 900
[19] Processing of biocompatible porous Ti and Mg
Wen, CE
Mabuchi, M
Yamada, Y
Shimojima, K
Chino, Y
Asahina, T
[J]. SCRIPTA MATERIALIA, 2001, 45 (10) : 1147 - 1153
[20] Pore structures of high-porosity NiTi alloys made from elemental powders with NaCl temporary space-holders
Zhao, Xingke
Sun, Hongbo
Lan, Lan
Huang, Jihua
Zhang, Hua
Wang, Yu
[J]. MATERIALS LETTERS, 2009, 63 (28) : 2402 - 2404

← 1 2 →