Dynamic constitutive models of Ti-6Al-4V based on isothermal ture stress-strain curves

被引:12
作者
Yan, Lan [1 ]
Jiang, Anna [1 ]
Li, Yaning [2 ]
Qiu, Tian [3 ]
Jiang, Feng [3 ]
Xie, Hong [4 ]
Wang, Fuzeng [3 ]
Wu, Xian [1 ]
Zhang, Yong [1 ]
机构
[1] Huaqiao Univ, Coll Mech Engn & Automat, Xiamen 361021, Peoples R China
[2] Northwest Inst Nonferrous Met Res, State Key Lab Porous Met Mat, Xian 710016, Peoples R China
[3] Huaqiao Univ, Inst Mfg Engn, Xiamen 361021, Peoples R China
[4] Dong Fang Turbine CO LTD, Dept Engn, Deyang 618000, Peoples R China
来源
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T | 2022年 / 19卷
基金
中国国家自然科学基金;
关键词
Dynamic mechanical properties; Temperature-dependent specific heat capacity; Adiabatic temperature rise; True stress-strain isothermal curves; Power-law model; Johnson-Cook model; SERRATED CHIP FORMATION; CUTTING PERFORMANCE; PVD COATINGS; WIDE-RANGE; ALLOY; TEMPERATURE; RATES; EQUATION; BEHAVIOR;
D O I
10.1016/j.jmrt.2022.06.164
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Ti-6Al-4V titanium alloy is a typical difficult-to-cut material used in many fields. The selection of cutting parameters exerts tremendous influences on the material removal process. Finite element numerical simulation is a low-cost method to obtain optimized cutting parameters. Finite element simulation requires the study of machining properties of machined materials. The material removal and related physical phenomena during machining are characterized by the dynamic mechanical properties of the machined material. In this paper, the dynamic mechanical properties of Ti-6Al-4V have been tested by the high temperature split Hopkinson pressure bar system to obtain true stress-strain curves under different conditions. The sensitivity of strain and temperature of Ti-6Al-4V has been analyzed. The influence of temperature-dependent specific heat capacity, which has been tested by a laser thermal conductivity tester, on adiabatic temperature rise has been considered. Adiabatic temperature rise has been calculated separately with constant specific heat capacity and temperature-dependent specific heat capacity. True stress-strain curves have been switched to true stress-strain isothermal curves to analyze separately the influence of strain rate and temperature on true stress. Based on true stress -strain isothermal curves, the constitutive models of power-law and Johnson-Cook have been introduced to fit the experimental results. The fitting results of the two constitutive models have been compared with the experiment results, which have an average error less than 6%. (C) 2022 The Author(s). Published by Elsevier B.V.
引用
收藏
页码:4733 / 4744
页数:12
相关论文
共 50 条
[1]   Stress-Strain Curves and Modified Material Constitutive Model for Ti-6Al-4V over the Wide Ranges of Strain Rate and Temperature [J].
Hou, Xin ;
Liu, Zhanqiang ;
Wang, Bing ;
Lv, Woyun ;
Liang, Xiaoliang ;
Hua, Yang .
MATERIALS, 2018, 11 (06)
[2]   Dynamic constitutive model of Fe-Cr-Ni stainless steel based on isothermal true stress-strain curves [J].
Du, Chenchong ;
Jiang, Feng ;
Guo, Bicheng ;
Zhang, Yong .
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2024, 31 :3901-3913
[3]   Constitutive relationship during isothermal compression of Ti-6Al-4V alloy sheet [J].
Zhang, Xuehua ;
Zhao, Yongqing ;
Zeng, Weidong .
MATERIALS LETTERS, 2019, 255
[4]   Material characterization, constitutive modeling and validation in hot stretch bending of Ti-6Al-4V profile [J].
Deng, Tongsheng ;
Li, Dongsheng ;
Li, Xiaoqiang ;
Ding, Pan ;
Zhao, Kai .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2016, 230 (03) :505-516
[5]   High-throughput characterization of the cyclic response of Ti-6Al-4V using spherical microindentation stress-strain protocols [J].
Johnson, Camilla ;
Mohan, Soumya ;
John, Reji ;
Kalidindi, Surya R. .
INTERNATIONAL JOURNAL OF FATIGUE, 2022, 161
[6]   A dynamic recrystallization based constitutive flow model for micro-machining of Ti-6Al-4V [J].
Yadav, Rahul ;
Chakladar, N. D. ;
Paul, Soumitra .
JOURNAL OF MANUFACTURING PROCESSES, 2022, 77 :463-484
[7]   A novel constitutive model for stress relaxation of Ti-6Al-4V alloy sheet [J].
Cui, Xuexi ;
Wu, Xiangdong ;
Wan, Min ;
Ma, Bolin ;
Zhang, Yanling .
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2019, 161
[8]   Modified constitutive models and cutting finite element simulation of Ti-6Al-4V alloy at cryogenic [J].
Lin, Huaixin ;
Jin, Gang ;
Luo, Shaokun ;
Wang, Guangyu ;
Li, Zhanjie .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2024, 238 (21) :10391-10403
[9]   Opposing and Driving Forces Associated with the Dynamic Transformation of Ti-6Al-4V [J].
Guo, Baoqi ;
Semiatin, S. L. ;
Liang, Jiangtao ;
Sun, Binhan ;
Jonas, John J. .
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2018, 49A (05) :1450-1454
[10]   A novel phenomenological constitutive model for Ti-6Al-4V at high temperature conditions and quasi-static strain rates [J].
Ashrafian, Mohammad Mahdi ;
Kordkheili, Seyed Ali Hosseini .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART G-JOURNAL OF AEROSPACE ENGINEERING, 2021, 235 (13) :1831-1842