Wear behavior of Al 5252 alloy reinforced with micrometric and nanometric SiC particles

被引：115

作者：

Moazami-Goudarzi, Mohammad ^{[1
]}

Akhlaghi, Farshad ^{[2
]}

机构：

[1] Islamic Azad Univ, Sci & Res Branch, Dept Mat Engn, Tehran, Iran

[2] Univ Tehran, Sch Met & Mat Engn, Coll Engn, POB 11155-4563, Tehran, Iran

来源：

TRIBOLOGY INTERNATIONAL | 2016年 / 102卷

关键词：

Aluminum based nano-composites; Dry sliding wear; Worn surface analysis; Wear debris; ALUMINUM-MATRIX COMPOSITES; DRY SLIDING WEAR; POWDER-METALLURGY METHOD; PARTICULATE REINFORCEMENT; MECHANICAL-PROPERTIES; MICROSTRUCTURE; NANOPARTICLES; RESISTANCE; FRICTION; SIZE;

D O I：

10.1016/j.triboint.2016.05.013

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The dry sliding wear behavior of Al 5252 alloy and its composites reinforced with nanometric or micrometric SiC particles is studied. The wear tests were conducted on hot extruded samples using a pin on the disc configuration under normal stresses: 03, 0.6 and 6.9 MPa at a sliding speed of 0.5 m/s and distance of 1000 m. The dominant wear mechanisms were determined using microstructural characterization, hardness measurement, EDS analysis as well as microscopic studies of wear surfaces and debris. The composite reinforced with micrometric SiC particles showed the lowest wear rate at the applied stresses of 0.3 and 0.6 MPa, while the nano-composites exhibited the best wear resistance at the normal Stress of 0.9 MPa. (C) 2016 Elsevier Ltd. All rights reserved.

引用

页码：28 / 37

页数：10

共 50 条

[41] Dry Sliding Wear Behavior of Zircon Sand Reinforced Al-Si Alloy
Kaur, Kamalpreet
Pandey, O. P.
TRIBOLOGY LETTERS, 2010, 38 (03) : 377 - 387
[42] Sliding wear Behavior of Cast Al-7075 Alloy Reinforced with MgO Particulates
Rao, K. V. Sreenivasa
Govindaraju
MATERIALS TODAY-PROCEEDINGS, 2017, 4 (10) : 11096 - 11101
[43] Flow stress behavior of nanometric Al2O3 particulate reinforced Al alloy composites manufactured by casting
Zhang, Zhimin
Yang, Yongbiao
Zhang, Xing
FRONTIERS OF ADVANCED MATERIALS AND ENGINEERING TECHNOLOGY, PTS 1-3, 2012, 430-432 : 1294 - +
[44] Pretreatment process of SiC particles and fabrication technology of SiC particulate reinforced Zn-Al alloy matrix composite
Li, ZQ
Wu, BY
Zhang, SY
MATERIALS SCIENCE AND TECHNOLOGY, 2001, 17 (08) : 954 - 960
[45] Effect of the SiC particle size on the dry sliding wear behavior of SiC and SiC–Gr-reinforced Al6061 composites
S. Mahdavi
F. Akhlaghi
Journal of Materials Science, 2011, 46 : 7883 - 7894
[46] Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles
Ahmadian, Hossein
Zhou, Tianfeng
Alansari, A.
Kumar, A. Senthil
Fathy, A.
Elmahdy, M.
Yu, Qian
Weijia, Guo
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2024, 31 : 4088 - 4103
[47] Effect of the SiC particle size on the dry sliding wear behavior of SiC and SiC-Gr-reinforced Al6061 composites
Mahdavi, S.
Akhlaghi, F.
JOURNAL OF MATERIALS SCIENCE, 2011, 46 (24) : 7883 - 7894
[48] Investigation into sliding wear performance of zinc-based alloy reinforced with SiC particles in dry and lubricated conditions
Prasad, B. K.
WEAR, 2007, 262 (3-4) : 262 - 273
[49] The Influence of Graphite Addition on the Abrasive Wear of AlMg10 Alloy Matrix Composites Reinforced with SiC Particles
Lagiewka, M.
Konopka, Z.
ARCHIVES OF FOUNDRY ENGINEERING, 2014, 14 (03) : 51 - 54
[50] Aging Precipitation Behavior and Mechanical Properties of 6013 Al Matrix Composites Reinforced by SiC Particles
Fu D.
Peng K.
Chen S.
Liu H.
Teng J.
Jiang F.
Zhang H.
Hunan Daxue Xuebao/Journal of Hunan University Natural Sciences, 2023, 50 (06): : 137 - 143

← 1 2 3 4 5 →