Effect of Vibration on Surface Texture during Machining Multiphase Microalloyed Steel

被引：4

作者：

Sivaraman, V. ^{[1
]}

Vijayaraghavan, L. ^{[2
]}

Sankaran, S. ^{[3
]}

机构：

[1] EGS Pillay Engn Coll, Dept Mech Engn, Nagapattinam 611002, Tamil Nadu, India

[2] IIT Madras, Dept Mech Engn, Madras 600036, Tamil Nadu, India

[3] IIT Madras, Dept Mat & Met Engn, Madras 600036, Tamil Nadu, India

来源：

45TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE (NAMRC 45) | 2017年 / 10卷

关键词：

Multiphase microalloyed steel; surface finish; vibration; CUTTING PARAMETERS; TOOL VIBRATIONS; ROUGHNESS; PREDICTION; GENERATION; SIGNALS;

D O I：

10.1016/j.promfg.2017.07.019

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Multiphase ferrite-bainite-martensite (FBM) microalloyed steel produced through two step cooling procedure was turned and compared with ferrite-pearlite (FP) microstructure and tempered-martensite (TM) microstructure to study the effect of vibration on surface finish. The cutting parameters like cutting speed, feed and depth of cut were varied to understand the parameter influence on surface finish due to vibration. The result shows that FBM microstructure steel gives better performance in terms of lower surface roughness and lower vibration compared to FP and TM microstructure steel. (C) 2017 The Authors. Published by Elsevier B.V.

引用

页码：429 / 435

页数：7

共 15 条

[1] Surface roughness prediction based on cutting parameters and tool vibrations in turning operations [J].

Abouelatta, OB ;

Mádl, J .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2001, 118 (1-3) :269-277

[2] CORRELATING TOOL WEAR, TOOL LIFE, SURFACE-ROUGHNESS AND TOOL VIBRATION IN FINISH TURNING WITH COATED CARBIDE TOOLS [J].

BONIFACIO, MER ;

DINIZ, AE .

WEAR, 1994, 173 (1-2) :137-144

[3] Development of a cutting tool condition monitoring system for high speed turning operation by vibration and strain analysis [J].

Chelladurai, H. ;

Jain, V. K. ;

Vyas, N. S. .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2008, 37 (5-6) :471-485

[4] The impact of cutting conditions on cutting forces and vibration signals in turning with plane face geometry inserts [J].

Dimla, DE .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2004, 155 :1708-1715

[5] On the prediction of surface roughness in the hard turning based on cutting parameters and tool vibrations [J].

Hessainia, Zahia ;

Belbah, Ahmed ;

Yallese, Mohamed Athmane ;

Mabrouki, Tarek ;

Rigal, Jean-Francois .

MEASUREMENT, 2013, 46 (05) :1671-1681

[6]

Kumar M. G., 2014, AIMTDR, V707

[7]

Pederiva R., 2016, INT J ADV MANUF TECH, P1

[8] Chatter in machining processes: A review [J].

Quintana, Guillem ;

Ciurana, Joaquim .

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2011, 51 (05) :363-376

[9] Low cycle fatigue behavior of a multiphase microalloyed medium carbon steel: comparison between ferrite-pearlite and quenched and tempered microstructures [J].

Sankaran, S ;

Sarma, VS ;

Padmanabhan, KA .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2003, 345 (1-2) :328-335

[10]

Siddhpura M., 2013, P WORLD ACAD SCI ENG, P62

← 1 2 →