Influence of heat treatment conditions on bending characteristics of 6063 aluminum alloy sheets

被引：21

作者：

Liu, Zhi-wen ^{[1
,2
]}

Li, Luo-xing ^{[1
,2
]}

Yi, Jie ^{[1
]}

Li, Shi-kang ^{[1
,2
]}

Wang, Zhen-hu ^{[1
,2
]}

Wang, Guan ^{[1
,3
]}

机构：

[1] Hunan Univ, State Key Lab Adv Design & Mfg Vehicle Body, Changsha 410082, Hunan, Peoples R China

[2] Hunan Univ, Coll Mech & Vehicle Engn, Changsha 410082, Hunan, Peoples R China

[3] Ningxia Univ, Coll Mech Engn, Yinchuan 750021, Peoples R China

来源：

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA | 2017年 / 27卷 / 07期

基金：

中国国家自然科学基金;

关键词：

6063 aluminum alloy; three-point bending; heat treatment conditions; bending characteristic; yield ratio; simulation; SPRINGBACK; TUBE;

D O I：

10.1016/S1003-6326(17)60170-5

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

Bending deformation behaviors of solution treated (ST), natural aged (NA) and T6 tempered 6063 aluminum alloy sheets were studied by three-point bending tests. The changes of bending force, interior angle, bending radius and sheet thickness in the fillet region were analyzed by experimental measurements and numerical simulations. The results showed that the bending characteristics were strongly dependent on the heat treatment conditions. The T6 alloy sheets were bent more sharply and local plastic deformation occurred severely in the fillet region. However, the ST and NA alloy sheets exhibited relatively uniform bending deformation and large bending radius. The bending force of T6 alloy was the highest, followed by the NA alloy and that of the ST alloy was minimum. After unloading, as compared with the ST and NA alloys, the springback of T6 alloys was markedly larger. The aging time showed a positive sensitivity on the springback and non-uniform bending deformability. The bending characteristics are attributed to the combined effects of yield strength, yield ratio and coefficient of neutral layer.

引用

页码：1498 / 1506

页数：9

共 19 条

[1] Improvement of ultimate tensile strength by artificial ageing and retrogression treatment of aluminium alloy 6061 [J].

Abundez, Arturo ;

Pereyra, Isa ;

Campillo, Bernardo ;

Serna, Sergio ;

Alcudia, Enrique ;

Molina, Arturo ;

Blanco, Andres ;

Mayen, Jan .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 668 :201-207

[2] Effect of various melt and heat treatment conditions on impact toughness of A356 aluminum alloy [J].

Elahi, M. Amne ;

Shabestari, S. G. .

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2016, 26 (04) :956-965

[3]

Frank, 1999, J MATER PROCESS TECH, P1

[4] Influence of the temperature on residual stresses and springback effect in an aluminium alloy [J].

Greze, R. ;

Manach, P. Y. ;

Laurent, H. ;

Thuillier, S. ;

Menezes, L. F. .

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2010, 52 (09) :1094-1100

[5] Evolution of neutral layer and microstructure of AZ31B magnesium alloy sheet during bending [J].

Huang, Guangsheng ;

Wang, Lifei ;

Zhang, Hua ;

Wang, Yanxia ;

Shi, Zhaoyang ;

Pan, Fusheng .

MATERIALS LETTERS, 2013, 98 :47-50

[6] Instrumented microindentation studies on long-term aged materials: work-hardening exponent and yield ratio as new degradation indicators [J].

Jang, JI ;

Choi, Y ;

Lee, YH ;

Kwon, D .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 395 (1-2) :295-300

[7] Numerical investigations on springback characteristics of aluminum sheet metal alloys in warm forming conditions [J].

Kim, Hong Seok ;

Koc, Muammer .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 204 (1-3) :370-383

[8] Effect of internal fluid pressure on quality of aluminum alloy tube in rotary draw bending [J].

Lazarescu, Lucian .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2013, 64 (1-4) :85-91

[9] Springback of extruded 2196-T8511 and 2099-T83 Al-Li alloys in stretch bending [J].

Liu, Tianjiao ;

Wang, Yongjun ;

Wu, Jianjun ;

Xia, Xiaojiao ;

Wang, Wei ;

Wang, Shunhong .

11TH INTERNATIONAL CONFERENCE ON TECHNOLOGY OF PLASTICITY, ICTP 2014, 2014, 81 :981-986

[10] Springback analysis of Z & T-section 2196-T8511 and 2099-T83 Al-Li alloys extrusions in displacement controlled cold stretch bending [J].

Liu, Tianjiao ;

Wang, Yongjun ;

Wu, Jianjun ;

Xia, Xiaojiao ;

Wang, Junbiao ;

Wang, Wei ;

Wang, Shunhong .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2015, 225 :295-309

← 1 2 →