Effect of Intercritical Heat Treatment on the Abrasive Wear Behaviour of Plain Carbon Dual Phase Steel

被引：0
|
作者：
Manoj, M. K. [1 ]
Pancholi, V. [1 ]
Nath, S. K. [1 ]
机构：
[1] IIT Roorkee, Dept Met Mat Engg, Roorkee, Uttar Pradesh, India
来源：
MICROSTRUCTURE AND TEXTURE IN STEELS AND OTHER MATERIALS | 2009年
关键词：
DP steel; Abrasive wear; Martensite; MICROSTRUCTURE;
D O I：
10.1007/978-1-84882-454-6_34
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
Dual phase (DP) steels have been prepared from low carbon steel (0.14% C) at intercritical temperature 740 degrees C and time is varied from 1 minute to 30 minutes followed by water quenching. These steels have been characterized by optical microscopy, FE-SEM, hardness measurements, tensile properties and electron backscattered diffraction (EBSD) studies. Tensile properties of a typical dual phase steel are found to be 805 MPa ultimate tensile strength with 18% total elongation. Martensite volume fraction of D P steel (determined by EBSD technique) prepared at 740 degrees C for 6 minutes is found to be 10.2% and the grain size of ferrite and martensite found to be 14.39 micron and 1.05 microns respectively. Abrasive wear resistance of dual phase steels has been determined by pin on drum wear testing machine. DP steels have been found to be 25% more wear resistant than that of normalized steel. Short intercritical heating time followed by water quenching gives higher wear resistance by virtue of smaller and well dispersed martensite island in the matrix of ferrite.
引用
收藏
页码：483 / 488
页数：6
相关论文
共 50 条
  • [31] Effect of Heat Treatment Hardening on the Dry Sliding Wear Behaviour of Mild Steel
    Lebudi, C. L.
    Phiri, R. R.
    Leso, T.
    Oladijo, O. P.
    MRS ADVANCES, 2020, 5 (23-24) : 1195 - 1202
  • [32] Effect of Heat Treatment Hardening on the Dry Sliding Wear Behaviour of Mild Steel
    C. L. Lebudi
    R. R. Phiri
    T. Leso
    O. P. Oladijo
    MRS Advances, 2020, 5 : 1195 - 1202
  • [33] THE EFFECT OF INTERCRITICAL ANNEALING PATH ON THE STRUCTURE OF DUAL-PHASE STEEL
    SINGH, V
    NATH, SK
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 1987, 40 (03): : 275 - 279
  • [34] The effect of intercritical heat treatment temperature on the tensile properties and work hardening behavior of ferrite-martensite dual phase steel sheets
    Movahed, P.
    Kolahgar, S.
    Marashi, S. P. H.
    Pouranvari, M.
    Parvin, N.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 518 (1-2): : 1 - 6
  • [35] Improved toughness and ductility in ferrite/acicular ferrite dual-phase steel through intercritical heat treatment
    Shi, Lei
    Yan, Zesheng
    Liu, Yongchang
    Zhang, Cheng
    Qiao, Zhixia
    Ning, Baoqun
    Li, Huijun
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 590 : 7 - 15
  • [36] Effect of microstructure on the oxidative wear behavior of plain carbon steel
    Abouei, V.
    Saghafian, H.
    Kheirandish, Sh.
    WEAR, 2007, 262 (9-10) : 1225 - 1231
  • [37] THE IMPROVEMENT OF 3-BODY ABRASIVE WEAR OF PLAIN CARBON-STEEL BY THERMOCHEMICAL TREATMENTS
    KIM, HJ
    KWEON, YG
    WEAR, 1994, 174 (1-2) : 201 - 208
  • [38] Wear characteristics of plain carbon steel
    Gupta, VK
    Pandey, OP
    INDIAN JOURNAL OF ENGINEERING AND MATERIALS SCIENCES, 2000, 7 (5-6) : 354 - 360
  • [39] The effect of intercritical heat treatment on the mechanical properties of AISI 3115 steel
    Maleque, MA
    Poon, Y
    Masjuki, HH
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2004, 153 : 482 - 487
  • [40] Tempering behavior of a plain carbon dual-phase steel
    Joarder, A., 1600, (25):
12345