Reliability and failure of face-milling tools when cutting stainless steel

被引：18
|
作者：
Lin, TR [1 ]
机构：
[1] Natl Huwei Inst Technol, Dept Mech Mfg Engn, Huwei 632, Taiwan
来源：
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 1998年 / 79卷 / 1-3期
关键词：
face-milling; feed-rate; stainless steel;
D O I：
10.1016/S0924-0136(97)00451-2
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This paper reports the results of experiments into the reliability and failure of tools in the face-milling of stainless steel. The effect of cutting conditions (cutting speed, feed, depth of cut) on the tool life, as determined by chipping, is investigated. The results show that the chipping distribution is a close approximation to the normal distribution and that the determination of cumulative probability could be determined after 10 iteration tests. From the stand-point of the tool life by chipping, the feed-rate range can be divided into three regions: in the high feed-rate region, the cutting edge of the tool is chipped with built-up edge; in the medium feed-rate region, the cutting edge of the tool is chipped with no built-up edge; whilst in the low feed-rate region chipping rarely occurs. It was observed also that a cutting speed of 85 m min(-1) is optimum for maximum volume of metal removed. (C) 1998 Elsevier Science S.A. All rights reserved.
引用
收藏
页码：41 / 46
页数：6
相关论文
共 50 条
  • [41] Finding the optimum cutting conditions for face milling 13% manganese steel using the Taguchi design method and predictive equations
    Speedie, James A.
    Black, Ian
    Ritchie, James M.
    THERMEC 2009 SUPPLEMENT: 6TH INTERNATIONAL CONFERENCE ON PROCESSING & MANUFACTURING OF ADVANCED MATERIALS, 2010, 89-91 : 527 - +
  • [42] Optimization of the Cutting Conditions (Vc, fz and doc) for Burr Minimization in Face Milling of Mould Steel
    Silva, Jefferson Duarte
    Saramago, Sezimaria de F. P.
    Machado, Aiisson Rocha
    JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2009, 31 (02) : 151 - 160
  • [43] Effect of Radial Depth on Vibration and Surface Roughness During Face Milling of Austenitic Stainless Steel
    申阳
    陈永洁
    张俐
    方海涛
    庞佳
    刘敏
    王社权
    马晓魁
    张京
    刘志林
    Transactions of Tianjin University, 2011, 17 (05) : 336 - 339
  • [44] Effect of radial depth on vibration and surface roughness during face milling of austenitic stainless steel
    Shen Y.
    Chen Y.
    Zhang L.
    Fang H.
    Pang J.
    Liu M.
    Wang S.
    Ma X.
    Zhang J.
    Liu Z.
    Transactions of Tianjin University, 2011, 17 (5) : 336 - 339
  • [45] Study of burr behavior in face milling of PH 13-8 Mo stainless steel
    da Silva, Luiz Carlos
    da Mota, Paulo Rosa
    da Silva, Marcio Bacci
    Ezugwu, Emmanuel Okechukwu
    Machado, Alisson Rocha
    CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2015, 8 : 34 - 42
  • [46] Sustainable Dry Machining of Stainless Steel with Microwave-Treated Tungsten Carbide Cutting Tools
    Babe, Itemogeng Bernatt
    Gupta, Kapil
    Chaubey, Sujeet Kumar
    MICROMACHINES, 2023, 14 (06)
  • [47] Analytical model to estimate optimum cutting conditions when turning free machining stainless steel
    Bothner, RMB
    Freckleton, JE
    STROJARSTVO, 1997, 39 (1-2): : 5 - 11
  • [48] Study of face milling of hardened AISI D3 steel with a special design of carbide tools
    H. R. Siller
    C. Vila
    C. A. Rodríguez
    J. V. Abellán
    The International Journal of Advanced Manufacturing Technology, 2009, 40 : 12 - 25
  • [49] Study of face milling of hardened AISI D3 steel with a special design of carbide tools
    Siller, H. R.
    Vila, C.
    Rodriguez, C. A.
    Abellan, J. V.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2009, 40 (1-2) : 12 - 25
  • [50] Analysis of the behaviour effect of face cutting edge inserts on surface roughness when milling steels with MQL lubrication
    Saluena-Berna, X.
    Ortiz-Marzo, J. A.
    Casals-Terre, J.
    ADVANCES IN MATERIALS PROCESSING TECHNOLOGIE, 2006, 526 : 25 - 30
12345