Cyclic deformation and twinning in a semi-solid processed AZ91D magnesium alloy

被引:63
作者
Patel, H. A. [1 ]
Chen, D. L. [1 ]
Bhole, S. D. [1 ]
Sadayappan, K. [2 ]
机构
[1] Ryerson Univ, Dept Mech & Ind Engn, Toronto, ON M5B 2K3, Canada
[2] Nat Resources Canada, CANMET Mat Technol Lab, Ottawa, ON K1A 0G1, Canada
来源
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2010年 / 528卷 / 01期
基金
加拿大创新基金会; 加拿大自然科学与工程研究理事会;
关键词
Magnesium alloy; Thixomolding; Cyclic deformation; Twinning; Pseudoelastic modulus; Strain ratio; DIE-CAST MAGNESIUM; FATIGUE BEHAVIOR; MECHANICAL-PROPERTIES; TENSILE PROPERTIES; STRAIN; MG; MICROSTRUCTURE; ANISOTROPY; DUCTILITY; POROSITY;
D O I
10.1016/j.msea.2010.09.016
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
To improve fuel economy and reduce greenhouse gas emissions, magnesium alloys are being considered for automotive and aerospace applications because of their high strength-to-weight ratio. The structural applications of magnesium components require understanding of low cycle fatigue (LCF) behavior, since cyclic or thermal stresses are frequently encountered in many structural applications. The objective of this study was to examine LCF behavior and the role of twinning on cyclic deformation characteristics in a semi-solid processed (thixomolded) AZ91D magnesium alloy. The semi-solid thixomolded alloy showed a significantly higher fatigue life than its die cast counterpart especially at the lower strain amplitudes. The alloy was cyclically stable at lower strain amplitudes (0.1-0.2%); exhibited cyclic softening followed by cyclic hardening for the remaining life at intermediate strain amplitudes (0.3-0.8%) and cyclic hardening at higher strain amplitudes (1.0-1.2%). As the total strain amplitude increased, the stress amplitude and plastic strain amplitude increased, while the pseudoelastic modulus decreased. Unlike the wrought magnesium alloys reported in the literature, the hysteresis loops of the thixomolded AZ91D alloy were symmetrical in tension and compression. However, a strong non-linear or pseudoelastic stress-strain characteristic remained in both ascending and descending phases especially at higher strain amplitudes due to the occurrence of twinning and detwinning during cyclic deformation. Two types of twins (wider lenticular extension twins and narrower banded contraction twins) were observed in some favorably oriented larger primary alpha-Mg grains near the fracture surface. Fatigue life increased with decreasing strain ratio, and partial mean stress relaxation occurred mainly in the initial 10-20% of fatigue life. Fatigue crack initiation was observed to occur from the specimen surface or near-surface defects, and crack propagation was characterized by striation-like features. (C) 2010 Elsevier B.V. All rights reserved.
引用
收藏
页码:208 / 219
页数:12
相关论文
共 72 条
[41]   Semi-solid processing technologies for magnesium alloys [J].
Li, XG ;
Xie, SS ;
Jiang, YX ;
Li, L .
MAGNESIUM - SCIENCE, TECHNOLOGY AND APPLICATIONS, 2005, 488-489 :307-312
[42]   Strain controlled cyclic deformation behavior of an extruded magnesium alloy [J].
Lin, X. Z. ;
Chen, D. L. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 496 (1-2) :106-113
[43]  
Liu Z, 1999, J MATER SCI LETT, V18, P1567, DOI 10.1023/A:1006699930049
[44]  
Liu Z, 2000, ACTA METALL SIN-ENGL, V13, P961
[45]   Cyclic deformation Behavior and potential automobile application of magnesium die casting alloys AZ91 and AM50 [J].
Liu, Zheng ;
Ji, Haitao ;
Lin, Li ;
Chen, Lijia ;
Wu, Wei ;
Yang, Lin .
THERMEC 2006, PTS 1-5, 2007, 539-543 :1626-+
[46]   FATIGUE BEHAVIOR OF SHORT ALUMINA FIBER REINFORCED AZ91 MAGNESIUM ALLOY METAL MATRIX COMPOSITE [J].
LLORCA, N ;
BLOYCE, A ;
YUE, TM .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1991, 135 :247-252
[47]   Reversible plastic strain during cyclic loading-unloading of Mg and Mg-Zn alloys [J].
Mann, G. E. ;
Sumitomo, T. ;
Caceres, C. H. ;
Griffiths, J. R. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 456 (1-2) :138-146
[48]   Microstructure and porosity in thixomolded Mg alloys and minimizing adverse effects on formability [J].
Mansoor, Bilal ;
Mukherjee, Sibasish ;
Ghosh, Amit .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 512 (1-2) :10-18
[49]   Influence of porosity on the fatigue limit of die cast magnesium and aluminium alloys [J].
Mayer, H ;
Papakyriacou, M ;
Zettl, B ;
Stanzl-Tschegg, SE .
INTERNATIONAL JOURNAL OF FATIGUE, 2003, 25 (03) :245-256
[50]  
Moore AR, 2004, MAGNESIUM TECHNOLOGY 2004, P263