Application of an in situ measuring system for the compensation of wall thickness variations during turning of thin-walled rings

被引：14

作者：

Stoebener, Dirk ^{[1
]}

Beekhuis, Bjorn ^{[2
]}

机构：

[1] Univ Bremen, Bremen Inst Metrol Automat & Qual Sci BIMAQ, D-28359 Bremen, Germany

[2] Fdn Inst Mat Sci IWT, D-28359 Bremen, Germany

来源：

CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2013年 / 62卷 / 01期

关键词：

Metrology; Compensation; Distortion engineering; BEARING RINGS; DISTORTION; DEVIATIONS;

D O I：

10.1016/j.cirp.2013.03.129

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Distortion engineering during turning of thin-walled rings requires a compensation of clamping system induced wall thickness deviations. Their in situ determination with an ultrasound system inside a turning centre is presented. A comparison between CMM-data and the ultrasound values shows a good agreement, even if the standard deviation of the ultrasound raw data is larger by one order of magnitude. In experiments the measured deviations served as the set-values for compensational movements of the cutting tool during the finishing cut. The results for three different clamping situations indicate that wall thickness variations induced by clamping systems can be reduced significantly. (c) 2013 CIRP.

引用

页码：511 / 514

页数：4

共 21 条

[1] Adapted Non-Circular Soft Turning of Bearing rings - Impact of process machine interactions on compensation potential [J].

Beekhuis, B. ;

Stoebener, D. ;

Brinksmeier, E. .

FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012, 2012, 1 :540-545

[2]

Benz M., 2002, THESIS RWTH AACHEN

[3] Distortion engineering -: Identification of causes for dimensional and form deviations of bearing rings [J].

Brinksmeier, E. ;

Soelter, J. ;

Grote, C. .

CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2007, 56 (01) :109-112

[4]

Brinksmeier E, 2010, P 2 CIRP C PROC MACH

[5] Distortion compensation strategies in the production process of bearing rings [J].

Dijkman, M. ;

Goch, G. .

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2009, 40 (5-6) :443-447

[6]

DIJKMAN M, 2007, P SICE ANN C TAK, P2984

[7] A GENERAL METHODOLOGY FOR MACHINE-TOOL ACCURACY ENHANCEMENT BY ERROR COMPENSATION [J].

DONMEZ, MA ;

BLOMQUIST, DS ;

HOCKEN, RJ ;

LIU, CR ;

BARASH, MM .

PRECISION ENGINEERING-JOURNAL OF THE AMERICAN SOCIETY FOR PRECISION ENGINEERING, 1986, 8 (04) :187-196

[8] Predictive compliance based model for compensation in multi-pass milling by on-machine probing [J].

Guiassa, R. ;

Mayer, J. R. R. ;

Kops, Lucjan .

CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2011, 60 (01) :391-394

[9] Experimental study of distortion phenomena in manufacturing chains [J].

Kessler, O ;

Prinz, C ;

Sackmann, T ;

Nowag, L ;

Surm, H ;

Frerichs, F ;

Lübben, T ;

Zoch, HW .

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2006, 37 (01) :11-18

[10]

Krautkramer J., 1969, ULTRASONIC TESTING M

← 1 2 3 →