Effect of microstructure on the surface finish during machining of V-microalloyed steel: Comparison between ferrite-bainite-martensite and ferrite-pearlite microstructures

被引：2

作者：

Sivaraman, V. ^{[1
]}

Vijayaraghavan, L. ^{[1
]}

Sankaran, S. ^{[2
]}

机构：

[1] Indian Inst Technol Madras, Dept Mech Engn, Madras 600036, Tamil Nadu, India

[2] Indian Inst Technol Madras, Dept Met & Mat Engn, Madras 600036, Tamil Nadu, India

来源：

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE | 2015年 / 229卷 / 08期

关键词：

Multiphase steel; surface roughness; CUTTING PARAMETERS; ROUGHNESS; FORCE;

D O I：

10.1177/0954405414535922

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Multiphase ferrite-bainite-martensite microalloyed steel produced through a two-step cooling followed by annealing route and a ferrite-pearlite steel obtained through air-cooling after forging were subjected to turning operation. The influence of process parameters such as cutting speed, feed and depth of cut on surface roughness on both materials was compared. The results show that the multiphase microalloyed steel exhibited high surface finish than air-cooled steel. The analysis of variance shows that the contribution of cutting speed and depth of cut on surface roughness are insignificant for both ferrite-bainite-martensite and ferrite-pearlite microstructures.

引用

页码：1463 / 1466

页数：4

共 11 条

[1] Analysis of surface roughness and cutting force components in hard turning with CBN tool: Prediction model and cutting conditions optimization
Aouici, Hamdi
Yallese, Mohamed Athmane
Chaoui, Kamel
Mabrouki, Tarek
Rigal, Jean-Francois
[J]. MEASUREMENT, 2012, 45 (03) : 344 - 353
[2] Determining the effect of cutting parameters on surface roughness in hard turning using the Taguchi method
Asilturk, Ilhan
Akkus, Harun
[J]. MEASUREMENT, 2011, 44 (09) : 1697 - 1704
[3] Influence of machining parameters on forces and surface roughness during finish hard turning of EN 31 steel
Bartarya, Gaurav
Choudhury, Sounak K.
[J]. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2014, 228 (09) : 1068 - 1080
[4] Experimental investigations to optimise and compare the machining performance of different coated carbide inserts during turning hardened steel
Chinchanikar, Satish
Choudhury, Sounak K.
[J]. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2014, 228 (09) : 1104 - 1117
[5] Characterization of machining of AISI 1045 steel over a wide range of cutting speeds. Part 1: investigation of contact phenomena
Iqbal, S. A.
Mativenga, P. T.
Sheikh, M. A.
[J]. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2007, 221 (05) : 909 - 916
[6] Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel
Lalwani, D. I.
Mehta, N. K.
Jain, P. K.
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 206 (1-3) : 167 - 179
[7] Microalloyed forging steels
Naylor, DJ
[J]. PROCEEDINGS OF THE INTERNATIONAL CONFERENCE ON MICROALLOYING IN STEELS, 1998, 284-2 : 83 - 93
[8] Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts
Sahoo, Ashok Kumar
Sahoo, Bidyadhar
[J]. MEASUREMENT, 2012, 45 (08) : 2153 - 2165
[9] Microstructurat evolution and tensile behaviour of medium carbon microalloyed steel processed through two thermomechanical routes
Sankaran, S
Sangal, S
Padmanabhan, KA
[J]. MATERIALS SCIENCE AND TECHNOLOGY, 2005, 21 (10) : 1152 - 1160
[10] Machinability of Multiphase Microalloyed Steel
Sivaraman, V.
Sankaran, S.
Vijayaraghavan, L.
[J]. 1ST CIRP GLOBAL WEB CONFERENCE: INTERDISCIPLINARY RESEARCH IN PRODUCTION ENGINEERING (CIRPE2012), 2012, 2 : 55 - 59

← 1 2 →