Microstructure and mechanical properties of γ′ strengthened Co-Ni-Al-W-base ODS alloys

被引:13
|
作者
Zhang, Lin [1 ]
Qu, Xuanhui [1 ]
Qin, Mingli [1 ]
Rafi-ud-Din [1 ]
He, Xinbo [1 ]
Liu, Ye [1 ]
机构
[1] Univ Sci & Technol Beijing, State Key Lab Adv Met & Mat, Beijing Key Lab Powder Met & Particulate Mat, Beijing 100083, Peoples R China
关键词
Alloys; Powder metallurgy; Electron microscopy; Microstructure; HIGH-TEMPERATURE STRENGTH; SUPERALLOY; PHASE; SYSTEM; DEFORMATION; REFINEMENT; STABILITY; FAILURE;
D O I
10.1016/j.matchemphys.2012.06.055
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
gamma ' precipitates strengthened Co-Ni-Al-W-base ODS alloys, produced by mechanical alloying, are promising high-temperature structural materials. The alloys were found to be composed of gamma/gamma ' two-phase region and discontinuously formed area. The element Ni was effective in enhancing the solubility limit of Al and W within gamma matrix, thus promoting the precipitation of gamma ' phase and restricting the formation of secondary phases, such as Co7W6, Co3W, and AlxCo phases. The flow stress of the alloys was effectively enhanced by the addition of Ni. The peak stress has decreased with increasing deformation temperature. The improved low-temperature strength was mainly attributed to the pining effect of oxide dispersion, gamma ' precipitates and fine-grained structure. The sharp fall in the yield strength in the temperature range of 600-700 degrees C was ascribed to grain boundary sliding, diffusion-controlled void formation, and the formation of shear band. (c) 2012 Elsevier B.V. All rights reserved.
引用
收藏
页码:371 / 378
页数:8
相关论文
共 50 条
  • [41] COMPARISON OF MECHANICAL PROPERTIES AND FRACTURE BEHAVIOUR OF CO-BASE AND NI-BASE ALLOYS
    Siegl, Jan
    Podhorna, Bozena
    Hrbacek, Karel
    Kucharova, Kveta
    21ST INTERNATIONAL CONFERENCE ON METALLURGY AND MATERIALS (METAL 2012), 2012, : 1288 - 1294
  • [42] Microstructure and mechanical properties of matrix alloy (Ni-Fe-Co-W) derived from tungsten heavy alloys
    Kiran, U. Ravi
    Babu, U. Chinta
    Nandi, H. K.
    Sarkar, Rajdeep
    Nandy, T. K.
    MATERIALS TODAY-PROCEEDINGS, 2021, 44 : 2403 - 2410
  • [43] Effects of Two-Phase Microstructure Morphology on Mechanical Properties in Co-Base Heat Resistant Alloys Strengthened by E21-(Co, Ni)3AlC Phase
    Kasakura, Mami
    Kimura, Yoshisato
    JOURNAL OF THE JAPAN INSTITUTE OF METALS AND MATERIALS, 2017, 81 (05) : 234 - 243
  • [44] The effect of Co on elastocaloric and mechanical properties of Ni-Co-Mn-Al alloys
    Xuan, Haicheng
    Cao, Ting
    Li, Shilong
    Wang, Libang
    Xie, Zhigao
    Liang, Xiaohong
    Chen, Fenghua
    Han, Peide
    SOLID STATE COMMUNICATIONS, 2019, 301
  • [45] Effect of Ta additions on microstructure and mechanical properties of a single-crystal Co-Al-W-base alloy
    Shi, L.
    Yu, J. J.
    Cui, C. Y.
    Sun, X. F.
    MATERIALS LETTERS, 2015, 149 : 58 - 61
  • [46] Influence of W Addition on Microstructure and Mechanical Properties of Al-12%Si Alloys
    Zykova, Anna
    Martyushev, Nikita
    Skeeba, Vadim
    Zadkov, Denis
    Kuzkin, Andrey
    MATERIALS, 2019, 12 (06):
  • [47] Microstructure and mechanical properties of Zr–Co–Al alloys prepared by rapid solidification
    Caiju Li
    Wenfei Lu
    Jun Tan
    Jingmei Tao
    Jianhong Yi
    Qixuan Zhang
    Yang Xi
    Journal of Materials Research, 2017, 32 : 2570 - 2577
  • [48] Microstructure and mechanical properties of Ti-45Al-2W-xC alloys
    Kamyshnykova, Kateryna
    Lapin, Juraj
    Pelachova, Tatiana
    Cegan, Tomas
    Jurica, Jan
    Volodarskaja, Anastasia
    INTERMETALLICS, 2022, 148
  • [49] Microstructure and mechanical properties of Al-base composites by addition of Al-Ni-Co decagonal quasicrystalline particles through a mechanical stirring route
    Zhu, Man
    Yang, Gencang
    Yao, Lijuan
    Cheng, Suling
    Zhou, Yaohe
    JOURNAL OF MATERIALS SCIENCE, 2010, 45 (14) : 3727 - 3734
  • [50] EFFECTS OF Ni ON MICROSTRUCTURAL EVOLUTION AND γ' DISSOLUTION OF NOVEL Co-Al-W BASE ALLOYS
    Xue Fei
    Mi Tao
    Wang Meiling
    Ding Xianfei
    Li Xianghui
    Feng Qiang
    ACTA METALLURGICA SINICA, 2014, 50 (07) : 845 - 853