Printing solder droplets for micro devices packages using pneumatic drop-on-demand (DOD) technique

被引:58
作者
Luo, Jun [1 ,2 ]
Qi, Le-hua [1 ,2 ]
Zhong, Song-yi [1 ]
Zhou, Ji-ming [1 ,2 ]
Li, He-jun [3 ]
机构
[1] NW Polytech Univ, Sch Mechatron, Xian 710072, Peoples R China
[2] Minist Educ, Key Lab Contemporary Design & Integrated Mfg Tech, Xian 710072, Peoples R China
[3] NW Polytech Univ, Sch Mat, Xian 710072, Peoples R China
基金
中国国家自然科学基金; 中国博士后科学基金;
关键词
Drop-on-demand (DOD); Interconnects; Uniform droplets; Data-driven soldering; MOLTEN-METAL DROPLETS; FREEFORM FABRICATION; TECHNOLOGY; DEPOSITION; SOLIDIFICATION; GENERATOR; BEHAVIOR; SURFACE; BREAKUP; STREAM;
D O I
10.1016/j.jmatprotec.2012.05.007
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
A pneumatic drop-on-demand (DOD) system has been applied to solder complex and dense interconnects of modern micro electronic devices. Initial parameters of uniform droplets were first measured. Then influences of experiment parameters, such as the crucible temperature, the substrate temperature and the droplet velocity on spread of solder droplets, were investigated experimentally and theoretically. The results showed that effects of impact velocity on the spreading could be negligible and the solder spreading process was driven by capillary forces because of the low Weber (We) number of depositing droplet. The influence of initial droplet temperature on the droplet spreading was not regular. The contact diameter of solder droplets on copper substrate increased when the substrate temperature increased from 443 K to 493 K. At last, copper cables were successfully soldered to pins of a flexible circuit using the direct solder deposition and re-melting process. The soldering results showed the feasibility of the data-driven soldering technique using the pneumatic DOD deposition technology. (C) 2012 Elsevier B.V. All rights reserved.
引用
收藏
页码:2066 / 2073
页数:8
相关论文
共 22 条
[1]  
Arun Kumar N., 2006, J LIGHTWAVE TECHNOL, V24, P1504
[2]   An experimental study of molten microdroplet surface deposition and solidification: Transient behavior and wetting angle dynamics [J].
Attinger, D ;
Zhao, Z ;
Poulikakos, D .
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME, 2000, 122 (03) :544-556
[3]   Impact of molten metal droplets on the tip of a pin projecting from a flat surface [J].
Azar, RG ;
Yang, Z ;
Chandra, S ;
Mostaghimi, J .
INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW, 2005, 26 (02) :334-347
[4]   Producing molten metal droplets with a pneumatic droplet-on-demand generator [J].
Cheng, SX ;
Li, TG ;
Chandra, S .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2005, 159 (03) :295-302
[5]  
Duthaler G. M., 1992, DESIGN DROPLET ON DE
[6]   Development of a drop-on-demand droplet generator for one-drop-fill technology [J].
Fan, Kuang-Chao ;
Chen, Jhih-Yuan ;
Wang, Ching-Hua ;
Pan, Wen-Chueh .
SENSORS AND ACTUATORS A-PHYSICAL, 2008, 147 (02) :649-655
[7]  
Fu Xiaowei, 1999, Acta Metallurgica Sinica, V35, P147
[8]   MODELING OF DROPLET DYNAMIC AND THERMAL HISTORIES DURING SPRAY FORMING .1. INDIVIDUAL DROPLET BEHAVIOR [J].
GRANT, PS ;
CANTOR, B ;
KATGERMAN, L .
ACTA METALLURGICA ET MATERIALIA, 1993, 41 (11) :3097-3108
[9]   Direct writing technology-Advances and developments [J].
Hon, K. K. B. ;
Li, L. ;
Hutchings, I. M. .
CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2008, 57 (02) :601-620
[10]  
Hsiao W. K., 2004, EFFECTS SURFACE PROP, P10