Burr formation in micro-machining aluminum, 6061-T6

被引：0
|
作者：
Lee, K [1 ]
Stirn, B [1 ]
Dornfeld, DA [1 ]
机构：
[1] Univ Calif Berkeley, Dept Mech Engn, Berkeley, CA 94720 USA
来源：
INITIATIVES OF PRECISION ENGINEERING AT THE BEGINNING OF A MILLENNIUM | 2001年
关键词：
burr formation; micro-machining; drilling; milling;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Experimental studies on micro-milling and micro-drilling in aluminum 6061-T6 have been carried out. A range of different cutting speeds, chip loads and depths of cut using a tool of 127 mum diameter were considered. Drilling experiments with different feed to diameter ratios, cutting speeds and two drill diameters were conducted. The influence of the cutting parameters on burr size and burr type was observed. A comparison to burr formation in conventional machining is presented.
引用
收藏
页码：47 / 51
页数：5
相关论文
共 37 条
  • [31] Experimental investigation on burr formation in vibration-assisted micro-milling of Ti-6Al-4V
    Zheng, Lu
    Chen, Wanqun
    Huo, Dehong
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2019, 233 (12) : 4112 - 4119
  • [32] Research on the modeling of burr formation process in micro-ball end milling operation on Ti-6Al-4V
    Chen, M. J.
    Ni, H. B.
    Wang, Z. J.
    Jiang, Y.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2012, 62 (9-12) : 901 - 912
  • [33] Influence of hexagonal boron nitride additive nanocutting fluid on the machining of AA6061-T6 alloy using minimum quality lubrication
    Kumar, Avinash
    Shrama, Anuj Kumar
    Gupta, T. V. K.
    Katiyar, Jitendra Kumar
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART E-JOURNAL OF PROCESS MECHANICAL ENGINEERING, 2022,
  • [34] Research on the modeling of burr formation process in micro-ball end milling operation on Ti–6Al–4V
    M. J. Chen
    H. B. Ni
    Z. J. Wang
    Y. Jiang
    The International Journal of Advanced Manufacturing Technology, 2012, 62 : 901 - 912
  • [35] Investigations on burr formation mechanisms in micro milling of high-aspect-ratio titanium alloy ti-6al-4 v structures
    Wu, Yang
    Chen, Ni
    Bian, Rong
    He, Ning
    Li, Zhenjun
    Li, Liang
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2020, 185 (185)
  • [36] Micro milling of titanium alloy Ti-6Al-4V: 3-D finite element modeling for prediction of chip flow and burr formation
    Özel T.
    Olleak A.
    Thepsonthi T.
    Production Engineering, 2017, 11 (4-5) : 435 - 444
  • [37] Evaluation of the drilling process in 6061-T6 Al-Mg-Si alloys using AISI M-35 diamond-like carbon coated high-speed steel drill
    Drumond, Ramon Martins
    da Silva, Ernane Rodrigues
    Ba, Elhadji Cheikh Talibouya
    Lima, Victor Esteves de Souza
    Barbosa, Jorge Wanderson
    Fernandes, Gustavo Henrique Nazareno
    Firpe, Pedro Miraglia
    Martins, Paulo Sergio
    TRIBOLOGY INTERNATIONAL, 2024, 192
1234