Burr formation in micro-machining aluminum, 6061-T6

被引：0

作者：

Lee, K ^{[1
]}

Stirn, B ^{[1
]}

Dornfeld, DA ^{[1
]}

机构：

[1] Univ Calif Berkeley, Dept Mech Engn, Berkeley, CA 94720 USA

来源：

INITIATIVES OF PRECISION ENGINEERING AT THE BEGINNING OF A MILLENNIUM | 2001年

关键词：

burr formation; micro-machining; drilling; milling;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Experimental studies on micro-milling and micro-drilling in aluminum 6061-T6 have been carried out. A range of different cutting speeds, chip loads and depths of cut using a tool of 127 mum diameter were considered. Drilling experiments with different feed to diameter ratios, cutting speeds and two drill diameters were conducted. The influence of the cutting parameters on burr size and burr type was observed. A comparison to burr formation in conventional machining is presented.

引用

页码：47 / 51

页数：5

共 37 条

[21] Simultaneous optimization of burrs size and surface finish when milling 6061-T6 aluminium alloy
Seyed Ali Niknam
Victor Songmene
International Journal of Precision Engineering and Manufacturing, 2013, 14 : 1311 - 1320
[22] Effect of micro-milling parameters on burr formation and surface roughness in aluminum microchannels puncher
Mokhtar, Mohd Saifuldin Mohd
Yusoff, Ahmad Razlan
JURNAL TRIBOLOGI, 2024, 41 : 129 - 143
[23] Experimental investigation on part quality and metallic particle emission when milling 6061-T6 aluminium alloy
Niknam S.A.
Kouam J.
Songmene V.
International Journal of Machining and Machinability of Materials, 2016, 18 (1-2): : 120 - 137
[24] A dynamic recrystallization based constitutive flow model for micro-machining of Ti-6Al-4V
Yadav, Rahul
Chakladar, N. D.
Paul, Soumitra
JOURNAL OF MANUFACTURING PROCESSES, 2022, 77 : 463 - 484
[25] Experimental investigations on the surface characteristics of abrasive waterjet-milled pockets in aluminium 6061-T6 alloy
Adsul, Sourabh
Srinivasu, D. S.
ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2022, 8 : 92 - 109
[26] Prevention of hillock formation during micro-machining of silicon by using OTS-SAM and SiO2 coatings
Oh, T-S.
Kim, H-J.
Kim, D-E.
CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2010, 59 (01) : 259 - 262
[27] VFCVD diamond-coated cutting tools for micro-machining titanium alloy Ti6Al4V
Jackson, Mark J.
Novakov, Tamara
Whitfield, Michael
Robinson, Grant
Handy, Rodney
Sein, Htet
Ahmed, Waqar
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 92 (5-8) : 2881 - 2918
[28] Theoretical model for subsurface microstructure prediction in micro-machining Ti-6Al-4V alloy - Experimental validation
Bai, Jinxuan
Bai, Qingshun
Tong, Zhen
Guo, Hui
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2018, 148 : 64 - 72
[29] VFCVD diamond-coated cutting tools for micro-machining titanium alloy Ti6Al4V
Mark J. Jackson
Tamara Novakov
Michael Whitfield
Grant Robinson
Rodney Handy
Htet Sein
Waqar Ahmed
The International Journal of Advanced Manufacturing Technology, 2017, 92 : 2881 - 2918
[30] Analysis of burr formation in finish machining of nickel-based superalloy with worn tools using micro-scale in-situ techniques
Zannoun, Hamzah
Schoop, Julius
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2023, 189

← 1 2 3 4 →