Burr formation in micro-machining aluminum, 6061-T6

被引：0
|
作者：
Lee, K [1 ]
Stirn, B [1 ]
Dornfeld, DA [1 ]
机构：
[1] Univ Calif Berkeley, Dept Mech Engn, Berkeley, CA 94720 USA
来源：
INITIATIVES OF PRECISION ENGINEERING AT THE BEGINNING OF A MILLENNIUM | 2001年
关键词：
burr formation; micro-machining; drilling; milling;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Experimental studies on micro-milling and micro-drilling in aluminum 6061-T6 have been carried out. A range of different cutting speeds, chip loads and depths of cut using a tool of 127 mum diameter were considered. Drilling experiments with different feed to diameter ratios, cutting speeds and two drill diameters were conducted. The influence of the cutting parameters on burr size and burr type was observed. A comparison to burr formation in conventional machining is presented.
引用
收藏
页码：47 / 51
页数：5
相关论文
共 37 条
  • [11] Residual stresses and surface damage when micromachining 6061-T6 aluminum alloy
    Abdul Sadat
    The International Journal of Advanced Manufacturing Technology, 2024, 130 : 4469 - 4477
  • [12] Investigations into peck drilling process for large aspect ratio microholes in aluminum 6061-T6
    Ravisubramanian, S.
    Shunmugam, M. S.
    MATERIALS AND MANUFACTURING PROCESSES, 2018, 33 (09) : 935 - 942
  • [13] Sustainability assessment of machining Al 6061-T6 using Taguchi-grey relation integrated approach
    Zaidi, Sajid Raza
    Butt, Shahid Ikramullah
    Khan, Muhammad Ali
    Faraz, Muhammad Iftikhar
    Jaffery, Syed Husain Imran
    Petru, Jana
    HELIYON, 2024, 10 (13)
  • [14] ANFIS-TLBO-based optimization of drilling parameters to minimize burr formation in aluminum 6061
    Mondal, Nripen
    Banik, Soumil
    Paul, Sumitava
    Sarkar, Srija
    Mandal, Sudip
    Ghosh, Sudipta
    MULTISCALE AND MULTIDISCIPLINARY MODELING EXPERIMENTS AND DESIGN, 2024, 7 (04) : 3607 - 3623
  • [15] Finite element modeling on micro-machining of graphene-reinforced aluminum matrix composites
    Hao Yu
    Zhenpeng He
    Jinbo Li
    Baichun Li
    Jia Xin
    Lianzheng Yao
    Fangchao Yan
    The International Journal of Advanced Manufacturing Technology, 2023, 124 : 97 - 110
  • [16] Finite element modeling on micro-machining of graphene-reinforced aluminum matrix composites
    Yu, Hao
    He, Zhenpeng
    Li, Jinbo
    Li, Baichun
    Xin, Jia
    Yao, Lianzheng
    Yan, Fangchao
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2023, 124 (1-2) : 97 - 110
  • [17] Fiber Laser Micro-machining of Ti-6Al-4V
    Sen, A.
    Doloi, B.
    Bhattacharyya, B.
    LASERS BASED MANUFACTURING, 2015, : 255 - 281
  • [18] Effects of lubrication modes on part quality during drilling 6061-T6 aluminium alloy
    Zedan, Yasser
    Songmene, Victor
    Kouam, Jules
    Masounave, Jacques
    Zedan, Y. (yasser.zedan.1@ens.etsmtl.ca), 1600, Inderscience Enterprises Ltd., 29, route de Pre-Bois, Case Postale 856, CH-1215 Geneva 15, CH-1215, Switzerland (13): : 231 - 252
  • [19] The effect of spindle speed, feed-rate and machining time to the surface roughness and burr formation of Aluminum Alloy 1100 in micro-milling operation
    Kiswanto, G.
    Zariatin, D. L.
    Ko, T. J.
    JOURNAL OF MANUFACTURING PROCESSES, 2014, 16 (04) : 435 - 450
  • [20] Simultaneous Optimization of Burrs Size and Surface Finish when Milling 6061-T6 Aluminium Alloy
    Niknam, Seyed Ali
    Songmene, Victor
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2013, 14 (08) : 1311 - 1320
1234